codice:
[17179590.888000] ndiswrapper version 1.15 loaded (preempt=yes,smp=yes)
[17179941.356000] ndiswrapper: driver netam772 (Advanced Micro Devices,10/27/2003,2.0.0.4) loaded
[17179941.360000] ndiswrapper (NdisMAllocateMapRegisters:863): buffer size too big: 4928
[17179941.360000] ndiswrapper (NdisMAllocateMapRegisters:871): buffer size too big: 4928
[17179941.360000] ndiswrapper: using irq 10
[17179941.360000] ndiswrapper (NdisWriteErrorLogEntry:246): log: C000138D, count: 3, return_address: dfa58b8d
[17179941.360000] ndiswrapper (NdisWriteErrorLogEntry:249): code: 0
[17179941.360000] ndiswrapper (NdisWriteErrorLogEntry:249): code: 5
[17179941.360000] ndiswrapper (NdisWriteErrorLogEntry:249): code: 0
[17179942.404000] wlan0: ndiswrapper ethernet device 00:06:f4:09:89:52 using driver netam772, 1022:2003.5.conf
[17179942.704000] ndiswrapper (set_packet_filter:713): filter not set: 0x00000009, 0x00002009
[17179944.940000] ndiswrapper (iw_set_encr:976): key 1 is not set
Non mi da più quegli errori con i comandi di configurazione vari
codice:
# Wireless LAN adapter configuration
#
# Theory of operation :
#
# The script attempts to match a block of settings to the specific wireless
# card inserted, the *first* block matching the card is used.
# The address format is "hwaddr", with * as a wildcard.
# 'hwaddr' is the unique MAC address identifier of the wireless card.
# The MAC address is usually printed on the card, or can be found via ifconfig.
# Some examples here use only half of the MAC address with a wildcard to
# match a whole family of cards...
#
# All the Wireless specific configuration is done through the Wireless
# Extensions, so we will just call 'iwconfig' with the right parameters
# defined below.
# Of course, you need to have iwconfig installled on your system.
# To download iwconfig, or for more info on Wireless Extensions :
# http://www.hpl.hp.com/personal/Jean_...nux/Tools.html
#
# Note : you don't need to fill all parameters, leave them blank, in most
# cases the driver will initialise itself with sane defaults values or
# automatically figure out the value... And no drivers do support all
# possible settings...
#
# -- This is a modified '/etc/pcmcia/wireless.opts' script --
# -- I added sections for Prism/GT and Atheros based cards --
# -- (supported by the prism54 and madwifi drivers) --
# -- 16/sep/2004 * Eric Hameleers --
#
VERBOSE=1
case "$HWADDR" in
## NOTE : Comment out the following five lines to activate the samples below ...
## --------- START SECTION TO REMOVE -----------
## Pick up any Access Point, should work on most 802.11 cards
//questo è l'indirizzo delle prime cifre dell'indirizzo hardware della mia scheda pcmcia
00:06:F4:*)
INFO="Configurazione della mia scheda"
ESSID="wireless-carlos"
MODE="Managed"
CHANNEL="2"
RATE="auto"
KEY="xxxxxxxxxxxxx"
;;
## ---------- END SECTION TO REMOVE ------------
# Here are a few examples with a few Wireless LANs supported...
# The matching is done on the first 3 bytes of the MAC address
# SMC2835W EZ Connect g 2.4GHz 54 Mbps Wireless Cardbus Adapter
00:04:E2:*)
INFO="SMC2835W EZ Connect g 2.4GHz 54 Mbps Wireless Cardbus Adapter"
# ESSID (extended network name) : My Network, any
ESSID="any"
# NWID/Domain (cell identifier) : 89AB, 100, off
NWID=""
# Operation mode : Ad-Hoc, Managed, Master, Repeater, Secondary, auto
MODE="Managed"
# Frequency or channel : 1, 2, 3 (channel) ; 2.422G, 2.46G (frequency)
FREQ=""
CHANNEL="7"
# Sensitivity (cell size + roaming speed) : 1, 2, 3 ; -70 (dBm)
SENS=""
# Bit rate : auto, 1M, 11M,54M
RATE="auto"
# Encryption key : 4567-89AB-CD, s:password
# Example for 40-bit encryption:
#KEY="883e-aa67-21 [1] key 5501-d0da-87 [2] key 91f5-3368-6b [3] key 2d73-31b7-96 [4]"
# Example for 104-bit encryption (aka 128-bit WEP):
#KEY="d5ad2f05abd048ecf10b1c80c7"
KEY=""
# RTS threshold : off, 500
RTS=""
# Fragmentation threshold : off, 1000
FRAG=""
# Other iwconfig parameters : power off, ap 01:23:45:67:89:AB
IWCONFIG=""
# iwspy parameters : + 01:23:45:67:89:AB
IWSPY=""
# iwpriv parameters : set_port 2, set_histo 50 60
IWPRIV=""
;;
# Multiband Atheros based 802.11a/b/g universal NIC cards
00:05:4E:*)
INFO="Multiband Atheros based 802.11a/b/g universal NIC"
# ESSID (extended network name) : My Network, any
ESSID="wireless-sidro"
# Operation mode : Ad-Hoc, Managed, Master, Repeater, Secondary, auto
MODE="Managed"
# Frequency or channel : 1, 2, 3 (channel) ; 2.422G, 2.46G (frequency)
FREQ=""
CHANNEL="2"
# Bit rate : auto, 1M, 11M,54M
RATE="auto"
# Encryption key : 4567-89AB-CD, s:password
# Example for 40-bit encryption:
#KEY="883e-aa67-21 [1] key 5501-d0da-87 [2] key 91f5-3368-6b [3] key 2d73-31b7-96 [4]"
# Example for 104-bit encryption (aka 128-bit WEP):
#KEY="d5ad2f05abd048ecf10b1c80c7"
KEY=""
# Other iwconfig parameters : power off, ap 01:23:45:67:89:AB
IWCONFIG=""
# iwspy parameters : + 01:23:45:67:89:AB
IWSPY=""
# iwpriv parameters : set_port 2, set_histo 50 60
IWPRIV=""
;;
# Lucent Wavelan IEEE (+ Orinoco, RoamAbout and ELSA)
# Note : wvlan_cs driver only, and version 1.0.4+ for encryption support
00:60:1D:*|00:02:2D:*)
INFO="Wavelan IEEE example (Lucent default settings)"
ESSID="Wavelan Network"
MODE="Managed"
#RATE="auto"
KEY="s:secu1"
# To set all four keys, use :
#KEY="s:secu1 [1] key s:secu2 [2] key s:secu3 [3] key s:secu4 [4] key [1]"
# For the RG 1000 Residential Gateway: The ESSID is the identifier on
# the unit, and the default key is the last 5 digits of the same.
#ESSID="084d70"
#KEY="s:84d70"
;;
# Cisco/Aironet 4800/3x0
# Note : MPL driver only (airo/airo_cs), version 1.3 or later
00:40:96:*|00:02:8A:*)
INFO="Cisco/Aironet example (Cisco default settings)"
ESSID="any"
# To set all four ESSID, use iwconfig v21 and the same trick as above
MODE="Managed"
#RATE="11M auto"
#KEY="d5ad2f05abd048ecf10b1c80c7"
KEY="off"
;;
# Samsung MagicLan (+ some other PrismII cards)
# Note : Samsung binary library driver, version 1.20 or later
00:00:F0:*|00:02:78:*)
INFO="Samsung MagicLan example (Samsung default settings)"
ESSID="any"
MODE="Managed"
CHANNEL="4"
RATE="auto"
#KEY="883e-aa67-21 [1] key 5501-d0da-87 [2] key 91f5-3368-6b [3] key 2d73-31b7-96 [4]"
#IWCONFIG="power on"
;;
# Raytheon Raylink/WebGear Aviator2.4
# Note : doesn't work yet, please use for debugging only :-(
00:00:8F:*|00:00:F1:*)
INFO="Raylink/Aviator2.4 example (Aviator default ad-hoc setting)"
ESSID="ADHOC_ESSID"
MODE="Ad-Hoc"
RATE="auto"
IWPRIV="set_framing 1"
;;
# Old Lucent Wavelan
08:00:0E:*)
INFO="Wavelan example (Lucent default settings)"
NWID="0100"
MODE="Ad-Hoc"
FREQ="2.425G"
KEY="off"
;;
# Netwave (Xircom Netwave/Netwave Airsurfer)
00:80:C7:*)
INFO="Netwave example (Netwave default settings)"
NWID="100"
KEY="00"
;;
# Proxim RangeLan2/Symphony (what is the MAC address ???)
XX:XX:XX:*)
INFO="Proxim RangeLan2/Symphony example"
NWID="0"
MODE="Master"
CHANNEL="15"
IWPRIV="setsubchan 1"
;;
# No Wires Needed Swallow 550 and 1100 setting (what is the MAC address ???)
XX:XX:XX:*)
INFO="NWN Swallow example"
ESSID="session"
KEY="0000-0000-00 open"
;;
# Symbol Spectrum24 setting (what is the MAC address ???)
XX:XX:XX:*)
INFO="Symbol Spectrum24 example"
ESSID="Essid string"
;;
# La mia scheda Atlantis-Land (decribe all possible settings)
00:06:F4:*)
INFO="Atlantis-Land 11Mbps"
# ESSID (extended network name) : My Network, any
ESSID="wireless-carlos"
# NWID/Domain (cell identifier) : 89AB, 100, off
#NWID=""
# Operation mode : Ad-Hoc, Managed, Master, Repeater, Secondary, auto
MODE="Managed"
# Frequency or channel : 1, 2, 3 (channel) ; 2.422G, 2.46G (frequency)
#FREQ=""
CHANNEL="2"
# Sensitivity (cell size + roaming speed) : 1, 2, 3 ; -70 (dBm)
#SENS=""
# Bit rate : auto, 1M, 11M
RATE="auto"
# Encryption key : 4567-89AB-CD, s:password
KEY="xxxxxxxxxxxxx"
# RTS threshold : off, 500
#RTS=""
# Fragmentation threshold : off, 1000
#FRAG=""
# Other iwconfig parameters : power off, ap 01:23:45:67:89:AB
#IWCONFIG=""
# iwspy parameters : + 01:23:45:67:89:AB
#IWSPY=""
# iwpriv parameters : set_port 2, set_histo 50 60
#IWPRIV=""
;;
esac
Ma non è che nella prima parte di questo file devo settare i parametri del mio access point con il suo indirizzo MAC? Io ho configurato la prima parte e l'ultima di questo file in maniera uguale...
Rispondi quotando
Originariamente inviata da caralu
