SuSE 9.1 personal eagle-usb

[nicaragua90]

Sono riuscito ad installare i driver eagle-usb su suse9.1 personal (dopo aver scaricato ed installato i vari: automake, autoconf, make, m4, glibc-devel, rp-pppoe e kernel-source) ho configurato il modem (eagleconfig) che mi ha caricato il modulo,inserito i dns in etc/ppp/resolv.config (almeno credo si chiami cosi non ricordo) adesso e fatto la connessione (startadsl) tutto ok funziona
al riavvio però non mi ricarica il modulo e quindi devo andare da console e digitare qualcosa tipo eagle.... -d
come posso evitare questo ogni volta e magare configurare anche l'applet (di cui non ricordo il nome )per connettermi senza dover aprire ogni volta il terminale
grazie

[nicaragua90]

questo mi restituisce appena avvio e tento di lanciare la connessione

linux:~ # startadsl


Modem is not operational!
Check eaglestat result to know its state!

linux:~ # eaglestat
eagle-usb status display
-------------------------------------------------------------
Driver version 2
USB Bus : 002 USB Device : 004 Dbg mask: 0x0
Ethernet Interface : none
MAC: 00:05:d8:20:d0:12
Tx Rate 0000000000 Rx Rate 0000000000 Crc 0000000000
FEC 0000000000 Margin 0000000000 Atten 0000000000 dB
VID-CPE 0000000000 VID-CO 0000000000 HEC 0000000000
VPI 0000000000 VCI 0000000000 Delin GOOD
Cells Rx 0000000000 Cells Tx 0000000000
Pkts Rx 0000000000 Pkts Tx 0000000000
OAM 0000000000 Bad VPI 0000000000 Bad CRC 0000000000
Oversiz. 0000000000

Modem waiting for driver response.
Please send DSP (eaglectrl -d)

linux:~ # eaglectrl -d
Options successfully sent to driver.
Using DSP code for POTS line
DSP code successfully loaded.
linux:~ #

dopo questo se faccio startadsl la connessione non va allora devo fare stopadsl e rifare startadsl
non so perchè ma me lo faceva anche con fedora (c'entra qualcos la sincronizzazione?)

aiutooooooooo

[nicaragua90]

qualcuno sa come posso caricare il modulo del driver all'avvio di suse
con fedora c'è l'apposito tool per caricare i servizi all'avvio ma con suse non so cosa fare

[andy caps]

prova a caricare il modulo e lanciare

generate_modprobe.conf


oppure controlla in
/etc/modprobe.conf se hai una riga da decommentare che riguarda il modulo


altrimenti prova ad utilizzare
etc/modprobe.conf.local

la sintassi corretta non la conosco

fai un po di prove mettendo ad esempio

/sbin/modprobe nome modulo

guarda man modprobe.conf comunque

[nicaragua90]

questo contiene il file ect/modprobe.conf


################################################## ######################
# Aliases - specify your hardware
################################################## ######################

install eth0 /bin/true
install eth1 /bin/true
install tr0 /bin/true
install scsi_hostadapter /bin/true
install fb0 /bin/true


# alias autofs autofs4

# install paride /sbin/modprobe --ignore-install paride && { /sbin/modprobe --ignore-install frpw; }
# remove paride { /sbin/modprobe -r --ignore-remove frpw; } ; /sbin/modprobe -r --ignore-remove paride

################################################## ######################
#
# Aliases for OSS
#
# These aliases will be changed by YaST2 sound configurator.
# If you would like to configure OSS drivers by yourself, please
# take a look at the files on /usr/src/linux/Documentation/sound.
#
################################################## ######################

install char-major-14 /bin/true
install sound /bin/true
install midi /bin/true

################################################## ######################
# Options; these are examples; uncomment and modify the lines you need
################################################## ######################

# options cdu31a cdu31a_port=0x340 cdu31a_irq=0
# options sbpcd sbpcd=0x230,1
# options aztcd aztcd=0x320
# options cm206 cm206=0x340,11
# options gscd gscd=0x340
# options mcd mcd=0x300,11
# options mcdx mcdx=0x300,11
# options optcd optcd=0x340
# options sjcd sjcd_base=0x340
# options sonycd535 sonycd535=0x340
# options isp16 isp16_cdrom_base=0x340 isp16_cdrom_irq=0 isp16_cdrom_dma=0 isp16_cdrom_type=Sanyo

# options ne io=0x300 irq=5

# Use this if you have two cards:
# options ne io=0x300,0x320 irq=5,7

# options tulip options=0
# options 3c59x options=0
# options 3c501 io=0x280 irq=5
# options 3c503 io=0x280 irq=5 xcvr=0
# options 3c505 io=0x300 irq=10
# options 3c507 io=0x300 irq=10
# options 3c509 irq=10
# options at1700 io=0x260 irq=10
# options smc-ultra io=0x200 irq=10
# options wd io=0x300 irq=10
# options smc9194 io=0x200 irq=10 ifport=0
# options e2100 io=0x300 irq=10 mem=0xd0000 xcvr=0
# options depca io=0x200 irq=7
# options ewrk3 io=0x300 irq=10
# options eexpress io=0x300 irq=10
# options hp-plus io=0x300 irq=10
# options hp io=0x300 irq=10
# options hp100 hp100_port=0x380
# options apricot io=0x300 irq=10
# options ac3200 io=0x300 irq=10 mem=0xd0000
# options de620 io=0x378 irq=7 bnc=1
# options ibmtr io=0xa20
# options arcnet io=0x300 irq=10 shmem=0xd0000
# options plip io=0x378 irq=7
# options eepro io=0x260 irq=10 mem=0x6000
# options eth16i io=0x2a0 irq=10
# options fmv18x io=0x220 irq=10
# options ni52 io=0x360 irq=9 memstart=0xd0000 memend=0xd4000
# options bttv pll=1 radio=0 card=0
# options tuner type=0
# options msp3400 once=1 simple=1

# install bttv /sbin/modprobe --ignore-install bttv && { /sbin/modprobe -k tuner; /sbin/modprobe -k msp3400; }
#

install dummy0 /sbin/modprobe -o dummy0 --ignore-install dummy
install dummy1 /sbin/modprobe -o dummy1 --ignore-install dummy

################################################## ######################
# cipe section
################################################## ######################

alias cipcb0 cipcb
alias cipcb1 cipcb

options cipcb cipe_debug=0

################################################## ######################
# block dev aliases
################################################## ######################

alias block-major-1 rd
alias block-major-2 floppy
install block-major-3 /bin/true
alias block-major-7 loop
alias block-major-8 sd_mod
alias block-major-11 sr_mod
alias block-major-13 xd
alias block-major-15 cdu31a
alias block-major-16 gscd
alias block-major-17 optcd
alias block-major-18 sjcd
alias block-major-20 mcdx
install block-major-22 /bin/true
alias block-major-23 mcd
alias block-major-24 sonycd535
alias block-major-25 sbpcd
alias block-major-26 sbpcd
alias block-major-27 sbpcd
alias block-major-28 sbpcd
alias block-major-29 aztcd
alias block-major-32 cm206
install block-major-33 /bin/true
install block-major-34 /bin/true
# network block device
install block-major-43 /bin/true
alias block-major-45 pd
alias block-major-46 pcd
alias block-major-47 pf
alias block-major-117 evms

################################################## ######################
# char dev aliases
################################################## ######################

alias char-major-6 lp
alias char-major-9 st
alias char-major-10-130 softdog
install char-major-10-134 /bin/true
install char-major-10-135 /bin/true
alias char-major-10-175 agpgart
alias char-major-10-181 toshiba
alias char-major-10-250 sonypi
options sonypi minor=250
install char-major-15 /bin/true
alias char-major-19 cyclades
alias char-major-20 cyclades
alias char-major-21 sg
alias char-major-27 ftape
install char-major-29 /bin/true
alias char-major-36 netlink_dev
# alias char-major-43 hisax
# alias char-major-44 hisax
# alias char-major-45 hisax
install char-major-43 /bin/true
install char-major-44 /bin/true
install char-major-45 /bin/true
alias char-major-48 riscom8
alias char-major-49 riscom8
alias char-major-67 coda
alias char-major-75 specialix
alias char-major-76 specialix
alias char-major-81 videodev
install char-major-81-0 /bin/true
install char-major-81-1 /bin/true
install char-major-81-2 /bin/true
install char-major-81-3 /bin/true

alias char-major-83 vtx
options vtx quiet=1

alias char-major-89 i2c-dev
alias char-major-96 pt
alias char-major-97 pg
alias char-major-107 3dfx
alias char-major-109 lvm-mod
# remove this if sound is configured
install char-major-116 /bin/true

################################################## ######################
# ppp over ethernet
# the kernel 2.2 uses pppox
# the kernel 2.4 uses pppoe
################################################## ######################

alias char-major-108 ppp_generic
alias char-major-144 pppoe
alias net-pf-24 pppoe

################################################## ######################
# IrDA
################################################## ######################

alias char-major-161 ircomm-tty

alias char-major-162 raw

################################################## ######################
# USB
################################################## ######################

install char-major-166 /bin/true

################################################## ######################
# Moxa Multiport Serial Boards
################################################## ######################

alias char-major-172 moxa
alias char-major-173 moxa

# options moxa type=2,,, baseaddr=0xdc000,,, numports=8,,,
alias char-major-174 mxser
alias char-major-175 mxser
# options mxser ioaddr=0x180

#alias char-major-180 usbcore

alias InterMezzo intermezzo
alias char-major-185 intermezzo

alias char-major-188 usbserial

alias char-major-206 osst
alias char-major-212 /bin/true

alias binfmt-204 binfmt_aout
alias binfmt-263 binfmt_aout
alias binfmt-264 binfmt_aout
alias binfmt-267 binfmt_aout
alias binfmt-0064 binfmt_aout
alias binfmt-0008 binfmt_aout

alias iso9660 isofs
alias tty-ldisc-1 slip
alias tty-ldisc-2 serio
alias tty-ldisc-5 mkiss

# alias tty-ldisc-7 6pack
install tty-ldisc-7 /bin/true

# IrDA
alias tty-ldisc-11 irtty

# alias ax0 mkiss
install ax0 /bin/true
# alias sp0 6pack
install sp0 /bin/true
alias slip0 slip
alias sl0 slip
alias slip1 slip
alias sl1 slip

################################################## ######################
# the kernel 2.2 uses ppp.o as ppp driver,
# the kernel 2.4 uses ppp_generic.o
################################################## ######################

alias ppp0 ppp_generic
alias ppp1 ppp_generic
alias tty-ldisc-3 ppp_async

alias plip0 plip
alias plip1 plip

# Tunnel interfaces
alias sit0 ipv6
alias gre0 ip_gre
alias ipip0 ipip

alias ppp-compress-18 ppp_mppe
alias ppp-compress-21 bsd_comp
alias ppp-compress-24 ppp_deflate
alias ppp-compress-26 ppp_deflate

alias net-pf-1 unix
alias net-pf-3 ax25
# install net-pf-3 /bin/true
alias net-pf-4 ipx
# install net-pf-4 /bin/true
alias net-pf-5 appletalk
# install net-pf-5 /bin/true
alias net-pf-6 netrom
# install net-pf-6 /bin/true
alias net-pf-10 ipv6
# install net-pf-10 /bin/true
alias net-pf-11 rose
# install net-pf-11 /bin/true
alias net-pf-15 af_key
alias net-pf-17 af_packet
alias net-pf-31 bluez

alias bt-proto-0 l2cap
alias bt-proto-2 sco
alias bt-proto-3 rfcomm
alias bt-proto-4 bnep

alias md-personality-1 linear
alias md-personality-2 raid0
alias md-personality-3 raid1
alias md-personality-4 raid5
alias md-personality-7 multipath

alias tap0 ethertap
alias tap1 ethertap
alias tap2 ethertap
alias tap3 ethertap
alias tap4 ethertap
alias tap5 ethertap
alias tap6 ethertap
alias tap7 ethertap
alias tap8 ethertap
alias tap9 ethertap
alias tap10 ethertap
alias tap11 ethertap
alias tap12 ethertap
alias tap13 ethertap
alias tap14 ethertap
alias tap15 ethertap

alias xfrm-type-2-50 esp4
alias xfrm-type-2-51 ah4
alias xfrm-type-2-108 ipcomp
alias xfrm-type-10-50 esp6
alias xfrm-type-10-51 ah6
alias xfrm-type-10-108 ipcomp6

# don't try to reset isa-pnp cards on startup
options isa-pnp isapnp_reset=0

# end of common part for modprobe.conf
# begin of i386 part for modprobe.conf

alias char-major-4 serial
alias char-major-5 serial

alias parport_lowlevel parport_pc
# options parport_pc io=0x378 irq=none,none
# If you have multiple parallel ports, specify them this way:
# options parport_pc io=0x378,0x278 irq=none,none

# Linux ACP modem (Mwave)
alias char-major-10-219 mwave
# options mwave dspirq=10 dspio=0x130 uartirq=3 uartio=0x2f8

# nVidia nforce chipset (network + audio)
#alias eth0 nvnet
#alias sound-slot-1 nvaudio
#alias usb-interface usb-ohci

# IBM thinkpad tpctl
# see /usr/share/doc/packages/tpctl/
alias char-major-10-170 thinkpad
# options thinkpad enable_smapi=0

# Linux-ABI
alias char-major-30 abi-ibcs
alias binfmt-0004 binfmt_coff
alias binfmt-332 abi-ibcs
alias binfmt-518 abi-ibcs
alias binfmt-002c abi-ibcs
alias personality-1 abi-ibcs
alias personality-2 abi-ibcs
alias personality-3 abi-sco
alias personality-4 abi-wyse
alias personality-5 abi-ibcs
alias personality-7 abi-ibcs
alias personality-13 abi-solaris
alias personality-14 abi-uw7
install binfmt_misc /sbin/modprobe --ignore-install binfmt_misc && { mount -t binfmt_misc none /proc/sys/fs/binfmt_misc; }
remove binfmt_misc { umount /proc/sys/fs/binfmt_misc; } ; /sbin/modprobe -r --ignore-remove binfmt_misc

# required for DRI support on SiS chips
options sisfb mode=none mem=12288

# end of i386 part for modprobe.conf
# please keep this at the end and add local modifications to modules.conf.local
include /etc/modprobe.conf.local
alias char-major-195* nvidia

[nicaragua90]

ho dovuto togliere un po di righe all'inizio ma non credo fossero interessanti

[andy caps]

ma come si chiama il modulo che vuoi caricare ?

hai lanciato da root

generate_modprobe.conf

[smilyzeus]

Puoi anche più semplicemente scrivere in
/etc/init.d/boot.local nell'ultima riga disponibile
modprobe modulochevuoicaricare
riavvii e sei a posto

[nicaragua90]

Ho risolto installando la nuova versione dei driver
adesso si caricano automaticamente.
grazie dell'aiuto