sulla slackware non riesco a far funzionare il mio modem ethernet
ho cercato di configurare così ma non fungecodice:root@darkstar:~# adsl-setup Welcome to the Roaring Penguin ADSL client setup. First, I will run some checks on your system to make sure the PPPoE client is installed properly... Looks good! Now, please enter some information: USER NAME >>> Enter your PPPoE user name (default mioaccount@tele2.it): mioaccount@TELE2.IT INTERFACE >>> Enter the Ethernet interface connected to the ADSL modem For Solaris, this is likely to be something like /dev/hme0. For Linux, it will be ethn, where 'n' is a number. (default eth0): Do you want the link to come up on demand, or stay up continuously? If you want it to come up on demand, enter the idle time in seconds after which the link should be dropped. If you want the link to stay up permanently, enter 'no' (two letters, lower-case.) NOTE: Demand-activated links do not interact well with dynamic IP addresses. You may have some problems with demand-activated links. >>> Enter the demand value (default no): DNS Please enter the IP address of your ISP's primary DNS server. If your ISP claims that 'the server will provide DNS addresses', enter 'server' (all lower-case) here. If you just press enter, I will assume you know what you are doing and not modify your DNS setup. >>> Enter the DNS information here: 130.244.127.161 Please enter the IP address of your ISP's secondary DNS server. If you just press enter, I will assume there is only one DNS server. >>> Enter the secondary DNS server address here: 130.244.127.169 PASSWORD >>> Please enter your PPPoE password: >>> Please re-enter your PPPoE password: FIREWALLING Please choose the firewall rules to use. Note that these rules are very basic. You are strongly encouraged to use a more sophisticated firewall setup; however, these will provide basic security. If you are running any servers on your machine, you must choose 'NONE' and set up firewalling yourself. Otherwise, the firewall rules will deny access to all standard servers like Web, e-mail, ftp, etc. If you are using SSH, the rules will block outgoing SSH connections which allocate a privileged source port. The firewall choices are: 0 - NONE: This script will not set any firewall rules. You are responsible for ensuring the security of your machine. You are STRONGLY recommended to use some kind of firewall rules. 1 - STANDALONE: Appropriate for a basic stand-alone web-surfing workstation 2 - MASQUERADE: Appropriate for a machine acting as an Internet gateway for a LAN >>> Choose a type of firewall (0-2): 1 ** Summary of what you entered ** Ethernet Interface: eth0 User name: mioaccount@tele2.it Activate-on-demand: No Primary DNS: 130.244.127.161 Secondary DNS: 130.244.127.169 Firewalling: STANDALONE >>> Accept these settings and adjust configuration files (y/n)? y Adjusting /etc/ppp/pppoe.conf Adjusting /etc/resolv.conf (But first backing it up to /etc/resolv.conf-bak) Adjusting /etc/ppp/pap-secrets and /etc/ppp/chap-secrets (But first backing it up to /etc/ppp/pap-secrets-bak) (But first backing it up to /etc/ppp/chap-secrets-bak) Congratulations, it should be all set up! Type 'adsl-start' to bring up your ADSL link and 'adsl-stop' to bring it down. Type 'adsl-status' to see the link status. root@darkstar:~# adsl-start ................TIMED OUT /usr/sbin/adsl-start: line 194: 2656 Terminated $CONNECT "$@" >/dev/null 2>&1 root@darkstar:~# dmesg | grep eth0 eth0: RealTek RTL8139 at 0xd0abc000, 00:a0:c5:b2:c6:90, IRQ 9 eth0: Identified 8139 chip type 'RTL-8100B/8139D' eth0: link up, 100Mbps, full-duplex, lpa 0x41E1 root@darkstar:~#
Rispondi quotando
difficile da dire
era una connesione a tele2 quella del portatile ?
