Ciao,ho uno strano problema..
Ho 2 videocards: S3 VIRGE (integrata)e NVIDIA TNT2
Quando uso un livecd vedo da verbose che riconosce nvidia e prova ad usare "nv" .
Qualche distro mi fa anche scegliere una delle 2.Quando prova a lanciare X" non riesce e da un messaggio"no screen found".
Il solo modo di avviare X ,sia da livecd che dopo installato su HD, è usare "vesa".
Ho provato ad installare tutti i pacchetti nvidia senza successo, almeno vorrei usare un driver per S3 VIRGE al posto di vesa..
Ho provato con 4-5 distribuzioni e ho sempre questo problema..
Grazie per un aiuto Ema
=====================================
le mie 2 videocards
=====================================
00:00.0 Host bridge: ALi Corporation M1621 (rev 04)
00:01.0 PCI bridge: ALi Corporation PCI to AGP Controller (rev 01)
00:02.0 USB Controller: ALi Corporation USB 1.1 Controller (rev 03)
00:07.0 ISA bridge: ALi Corporation M1533/M1535 PCI to ISA Bridge [Aladdin IV/V/V+] (rev c3)
00:0c.0 Multimedia audio controller: C-Media Electronics Inc CM8738 (rev 10)
00:0c.1 Communication controller: C-Media Electronics Inc CM8738 (rev 10)
00:0f.0 IDE interface: ALi Corporation M5229 IDE (rev c2)
00:12.0 VGA compatible controller: S3 Inc. 86c325 [ViRGE] (rev 05)
00:14.0 Ethernet controller: MYSON Technology Inc SURECOM EP-320X-S 100/10M Ethernet PCI Adapter
01:00.0 VGA compatible controller: nVidia Corporation NV5 [Aladdin TNT2] (rev 20)
=================================================
my xorg.conf
================================================
Section "ServerLayout"
Identifier "XFree86 Configured"
Screen 0 "Screen0" 0 0
InputDevice "Keyboard0" "CoreKeyboard"
# PS/2 Mouse using /dev/input/mice in Kernel 2.6
# Serial Mouse not detected
InputDevice "USB Mouse" "CorePointer"
EndSection
Section "ServerFlags"
Option "AllowMouseOpenFail" "true"
EndSection
EndSection
Section "Module"
Load "ddc" # ddc probing of monitor
Load "GLcore"
Load "dbe"
Load "dri"
Load "extmod"
Load "glx"
Load "bitmap" # bitmap-fonts
Load "speedo"
Load "type1"
Load "freetype"
Load "record"
EndSection
Section "InputDevice"
Identifier "Keyboard0"
Driver "keyboard"
Option "CoreKeyboard"
Option "XkbRules" "xfree86"
Option "XkbModel" "pc105"
Option "XkbLayout" "it"
Option "XkbOptions" "grp:shift_toggle"
EndSection
Section "InputDevice"
Identifier "Serial Mouse"
Driver "mouse"
Option "Protocol" "Microsoft"
Option "Device" "/dev/ttyS0"
Option "Emulate3Buttons" "true"
Option "Emulate3Timeout" "70"
Option "SendCoreEvents" "true"
EndSection
Section "InputDevice"
Identifier "PS/2 Mouse"
Driver "mouse"
Option "Protocol" "auto"
Option "ZAxisMapping" "4 5"
Option "Device" "/dev/psaux"
Option "Emulate3Buttons" "true"
Option "Emulate3Timeout" "70"
Option "SendCoreEvents" "true"
EndSection
Section "InputDevice"
Identifier "USB Mouse"
Driver "mouse"
Option "Device" "/dev/input/mice"
Option "SendCoreEvents" "true"
Option "Protocol" "IMPS/2"
Option "ZAxisMapping" "4 5"
Option "Buttons" "5"
EndSection
# Auto-generated by KNOPPIX mkxf86config
Section "Monitor"
Identifier "Monitor0"
Option "DPMS" "true"
ModelName "Old Monitor (no DDC)"
# HorizSync 28.0 - 78.0
HorizSync 31.0 - 60.0
# VertRefresh 50.0 - 76.0
VertRefresh 56.0 - 75.0
EndSection
Section "Device"
### Available Driver options are:-
# sw_cursor is needed for some ati and radeon cards
#Option "sw_cursor"
#Option "hw_cursor"
#Option "NoAccel"
#Option "ShowCache"
#Option "ShadowFB"
#Option "UseFBDev"
#Option "Rotate"
Identifier "Card0"
# The following line is auto-generated by KNOPPIX mkxf86config
Driver "vesa"
VendorName "All"
BoardName "All"
# BusID "PCI:1:0:0"
EndSection
Section "Screen"
Identifier "Screen0"
Device "Card0"
Monitor "Monitor0"
DefaultColorDepth 16
SubSection "Display"
Depth 1
Modes "1024x768" "800x600" "640x480"
EndSubSection
SubSection "Display"
Depth 4
Modes "1024x768" "800x600" "640x480"
EndSubSection
SubSection "Display"
Rispondi quotando
).
