Visualizzazione dei risultati da 1 a 2 su 2

Discussione: Route

  1. #1

    Route

    Ciao, ho appena reistalalto al suse 9.0 e gauardando tra il comando route non trovo l'instradamento della mia scheda di loopback:



    Kernel IP routing table
    Destination Gateway Genmask Flags Metric Ref Use Iface
    192.168.100.1 * 255.255.255.255 UH 0 0 0 ppp0
    192.168.0.0 * 255.255.255.0 U 0 0 0 eth0
    default 192.168.100.1 0.0.0.0 UG 0 0 0 ppp0

    mentre questo è l'ifconfig:

    linux:~/script # ifconfig
    eth0 Link encap:Ethernet HWaddr 00:20:ED:2F:44:1D
    inet addr:192.168.0.1 Bcast:192.168.0.255 Mask:255.255.255.0
    inet6 addr: fe80::220:edff:fe2f:441d/64 Scope:Link
    UP BROADCAST NOTRAILERS RUNNING MULTICAST MTU:1500 Metric:1
    RX packets:1107 errors:0 dropped:0 overruns:0 frame:0
    TX packets:313 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:100
    RX bytes:119827 (117.0 Kb) TX bytes:155875 (152.2 Kb)
    Interrupt:11 Base address:0x3f00

    lo Link encap:Local Loopback
    inet addr:127.0.0.1 Mask:255.0.0.0
    inet6 addr: ::1/128 Scope:Host
    UP LOOPBACK RUNNING MTU:16436 Metric:1
    RX packets:96 errors:0 dropped:0 overruns:0 frame:0
    TX packets:96 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:0
    RX bytes:6364 (6.2 Kb) TX bytes:6364 (6.2 Kb)

    ppp0 Link encap:Point-to-Point Protocol
    inet addr:82.51.***.** P-t-P:192.168.100.1 Mask:255.255.255.255
    UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1
    RX packets:7521 errors:0 dropped:0 overruns:0 frame:0
    TX packets:8228 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:3
    RX bytes:1425596 (1.3 Mb) TX bytes:464460 (453.5 Kb)

    sit0 Link encap:IPv6-in-IPv4
    inet6 addr: 2001:6b8:0:600::2452/0 Scope:Global
    inet6 addr: ::82.51.1**.**/96 Scope:Compat
    inet6 addr: ::127.0.0.1/96 Scope:Unknown
    UP RUNNING NOARP MTU:1480 Metric:1
    RX packets:0 errors:0 dropped:0 overruns:0 frame:0
    TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:0
    RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)

    Siccome sto cercando di mettere ipv6, e presumo che non vada per questo motivo, qualcuno sa dirmi come fare ad installare la loopback nel routing?

    infatti se eseguo lo script di instalalzoione ipv6:
    arrakis:~/ipv6 # ./act.sh
    SIOCADDRT: Invalid argument

    Qualcuno sa aiutarmi?

  2. #2
    :quote:

Permessi di invio

  • Non puoi inserire discussioni
  • Non puoi inserire repliche
  • Non puoi inserire allegati
  • Non puoi modificare i tuoi messaggi
  •  
Powered by vBulletin® Version 4.2.1
Copyright © 2024 vBulletin Solutions, Inc. All rights reserved.