Il driver del cavo me lo trova:
codice:
#cat /proc/bus/usb/devices
T: Bus=03 Lev=01 Prnt=01 Port=01 Cnt=02 Dev#= 5 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=ff(vend.) Sub=00 Prot=ff MxPS= 8 #Cfgs= 1
P: Vendor=0421 ProdID=0800 Rev= 3.0a
S: Product=Nokia Connectivity Cable DKU-5
C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr= 64mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
E: Ad=86(I) Atr=03(Int.) MxPS= 64 Ivl=1ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 32 Ivl=0ms
ma quando chiedo il rilevamento(nel pc c'è anche installato un modem generico winmodem) non mi trova nessun modem:
codice:
#wvdialconf /etc/wvdialconf.conf
Port Scan<*1>: Scanning ttyS0 first, /dev/modem is a link to it.
ttyS0<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud
ttyS0<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baud
ttyS0<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up.
ircomm0<*1>: ATQ0 V1 E1 -- failed at 9600 and 19200 baud.
ircomm1<*1>: ATQ0 V1 E1 -- failed at 9600 and 19200 baud.
ircomm2<*1>: ATQ0 V1 E1 -- failed at 9600 and 19200 baud.
ircomm3<*1>: ATQ0 V1 E1 -- failed at 9600 and 19200 baud.
ircomm4<*1>: ATQ0 V1 E1 -- failed at 9600 and 19200 baud.
ircomm5<*1>: ATQ0 V1 E1 -- failed at 9600 and 19200 baud.
ircomm6<*1>: ATQ0 V1 E1 -- failed at 9600 and 19200 baud.
ircomm7<*1>: ATQ0 V1 E1 -- failed at 9600 and 19200 baud.
ircomm8<*1>: ATQ0 V1 E1 -- failed at 9600 and 19200 baud.
ircomm9<*1>: ATQ0 V1 E1 -- failed at 9600 and 19200 baud.
Port Scan<*1>: S10 S11 S12 S13 S14 S15 S16 S17
Port Scan<*1>: S18 S19 S20 S21 S22 S23
ttySG0<Info>: No such device or address
Port Scan<*1>: SG0
ttyACM0<Info>: No such device or address
Port Scan<*1>: ACM0
ttyACM1<Info>: No such device or address
Port Scan<*1>: ACM1
ttyACM2<Info>: No such device or address
Port Scan<*1>: ACM2
ttyACM3<Info>: No such device or address
Port Scan<*1>: ACM3
ttyLT0<Info>: No such device or address
Port Scan<*1>: LT0 USB0 USB1 USB2 USB3
ircomm10<*1>: ATQ0 V1 E1 -- failed at 9600 and 19200 baud.
ircomm11<*1>: ATQ0 V1 E1 -- failed at 9600 and 19200 baud.
ircomm12<*1>: ATQ0 V1 E1 -- failed at 9600 and 19200 baud.
ircomm13<*1>: ATQ0 V1 E1 -- failed at 9600 and 19200 baud.
ircomm14<*1>: ATQ0 V1 E1 -- failed at 9600 and 19200 baud.
ircomm15<*1>: ATQ0 V1 E1 -- failed at 9600 and 19200 baud.
ircomm16<Info>: Device or resource busy
Port Scan<*1>: ircomm16
ircomm17<Info>: Device or resource busy
Port Scan<*1>: ircomm17
ircomm18<Info>: Device or resource busy
Port Scan<*1>: ircomm18
ircomm19<Info>: Device or resource busy
Port Scan<*1>: ircomm19
ircomm20<*1>: ATQ0 V1 E1 -- failed at 9600 and 19200 baud.
In windows è sulla porta COM5, ho anche installato easyconnect ma non riesce ad aprire la porta. C'è un modo per montare il dispositivo o devo scaricare dei driver specifici?
per Alexxo: ho letto il tuo post, con che cavo ti sei connesso?