PDA

Visualizza la versione completa : Connessione adsl in timeout


Shenk87
15-05-2005, 21:42
sulla slackware non riesco a far funzionare il mio modem ethernet



root@darkstar:~# adsl-setup
Welcome to the Roaring Penguin ADSL client setup. First, I will run
some checks on your system to make sure the PPPoE client is installed
properly...

Looks good! Now, please enter some information:

USER NAME

>>> Enter your PPPoE user name (default mioaccount@tele2.it): mioaccount@TELE2.IT

INTERFACE

>>> Enter the Ethernet interface connected to the ADSL modem
For Solaris, this is likely to be something like /dev/hme0.
For Linux, it will be ethn, where 'n' is a number.
(default eth0):

Do you want the link to come up on demand, or stay up continuously?
If you want it to come up on demand, enter the idle time in seconds
after which the link should be dropped. If you want the link to
stay up permanently, enter 'no' (two letters, lower-case.)
NOTE: Demand-activated links do not interact well with dynamic IP
addresses. You may have some problems with demand-activated links.
>>> Enter the demand value (default no):

DNS

Please enter the IP address of your ISP's primary DNS server.
If your ISP claims that 'the server will provide DNS addresses',
enter 'server' (all lower-case) here.
If you just press enter, I will assume you know what you are
doing and not modify your DNS setup.
>>> Enter the DNS information here: 130.244.127.161
Please enter the IP address of your ISP's secondary DNS server.
If you just press enter, I will assume there is only one DNS server.
>>> Enter the secondary DNS server address here: 130.244.127.169

PASSWORD

>>> Please enter your PPPoE password:
>>> Please re-enter your PPPoE password:

FIREWALLING

Please choose the firewall rules to use. Note that these rules are
very basic. You are strongly encouraged to use a more sophisticated
firewall setup; however, these will provide basic security. If you
are running any servers on your machine, you must choose 'NONE' and
set up firewalling yourself. Otherwise, the firewall rules will deny
access to all standard servers like Web, e-mail, ftp, etc. If you
are using SSH, the rules will block outgoing SSH connections which
allocate a privileged source port.

The firewall choices are:
0 - NONE: This script will not set any firewall rules. You are responsible
for ensuring the security of your machine. You are STRONGLY
recommended to use some kind of firewall rules.
1 - STANDALONE: Appropriate for a basic stand-alone web-surfing workstation
2 - MASQUERADE: Appropriate for a machine acting as an Internet gateway
for a LAN
>>> Choose a type of firewall (0-2): 1

** Summary of what you entered **

Ethernet Interface: eth0
User name: mioaccount@tele2.it
Activate-on-demand: No
Primary DNS: 130.244.127.161
Secondary DNS: 130.244.127.169
Firewalling: STANDALONE

>>> Accept these settings and adjust configuration files (y/n)? y
Adjusting /etc/ppp/pppoe.conf
Adjusting /etc/resolv.conf
(But first backing it up to /etc/resolv.conf-bak)
Adjusting /etc/ppp/pap-secrets and /etc/ppp/chap-secrets
(But first backing it up to /etc/ppp/pap-secrets-bak)
(But first backing it up to /etc/ppp/chap-secrets-bak)



Congratulations, it should be all set up!

Type 'adsl-start' to bring up your ADSL link and 'adsl-stop' to bring
it down. Type 'adsl-status' to see the link status.
root@darkstar:~# adsl-start
................TIMED OUT
/usr/sbin/adsl-start: line 194: 2656 Terminated $CONNECT "$@" >/dev/null 2>&1
root@darkstar:~# dmesg | grep eth0
eth0: RealTek RTL8139 at 0xd0abc000, 00:a0:c5:b2:c6:90, IRQ 9
eth0: Identified 8139 chip type 'RTL-8100B/8139D'
eth0: link up, 100Mbps, full-duplex, lpa 0x41E1
root@darkstar:~#


ho cercato di configurare cos ma non funge

andy caps
15-05-2005, 21:57
:confused: difficile da dire
se sei sicuro dei dns

a me successo che il sistema metteva su due eth0 al posto di eth1

dai un dmesg | grep eth e controlla se hai due schede
guarda di avere caricato ppp-deflate

prova un dns diverso
ricontrolla password e user

Shenk87
15-05-2005, 22:33
i dns li ho presi da qu http://www.sandrodiremigio.com/documenti/tutorials/pop3smtpnntp.htm

dmesg | grep eth
mi restituisce solo eth0



guarda di avere caricato ppp-deflate


come faccio?

andy caps
15-05-2005, 23:08
I DNS sono quelli consigliati da teledue

ma hai un modem o un router ?

per caricare ppp-deflate dai da terminale di root
modprobe ppp-deflate

dai un lsmod per vedere se caricato
se hai impostato un gateway nell'installazione lo devi togliere

dai il comando route -n

poi se vedi un gw dai
route del default gw 192.168.1.0 o il numero che vedi

Shenk87
16-05-2005, 00:02
uso un modem ethernet. la cosa strana che mi fa pensare a un qualche mio errore nella configurazione che un mese fa, gi configurai felicemente questo modem sul portatile.

se faccio modprobe ppp-deflate mi dice can't locate module o qualcosa del genere. in lsmod non caricato, se faccio route -n non vedo nessun gw, gli unici indirizzi sono 127.0.0.1 e 255.0.0.0

andy caps
16-05-2005, 01:32
prova modprobe ppp_deflate o comuque dai un
modprobe -l | grep ppp e guarda cosa hai

:bh: era una connesione a tele2 quella del portatile ?

Shenk87
16-05-2005, 12:26
ho sistemato! ho provato a mettere la password tutta con le lettere minuscole ed andato, strano perch quelli di tele2 mi avevano detto "tutto maiuscolo", boh, l'importante che funziona :ciauz:

Loading