Salve, ho installato Linux SUSE 10.
non capisco come posso accedere al Kernel, in quanto voglio abilitare la mia penna usb.
Mi potete dire passo dopo passo per accedere alla schermata della configurazione.
GRAZIIIIIIIIIIIIIIIIEEEEEEEEEEEEEE???????????????
al kernel non devi accedere
suse ha gia tutti i moduli e probabilmente li ha caricati gia
apri un terminale e scrivi su ( esse u )
dopo su metti la password di root e controlla con il comando
lsmod | grep usb se ha caricato i vari uhci ehci e usb-storage
se sono caricati il comando
fdisk -l ( elle minuscola ) ti dice se la vede
se non sono caricati caricali con
modprobe usb-storage
modprobe uhci-hcd ( o ehci o ohci dipende dalla tua scheda madre )
oltre ai vari hda o hdb dovresti vedere un sda o sdb o altro
poi ad esempio mkdir /mnt/usbpen
mount /dev/sda /mnt/usbpen carica in /mnt/usbpen la tua penna
per favore mi puoi dire cosa devo fare=====
col comando lsmod :
Module Size Used by
ipt_pkttype 1664 1
ipt_LOG 6912 7
ipt_limit 2304 7
cpufreq_ondemand 6044 1
cpufreq_userspace 4444 0
cpufreq_powersave 1792 0
powernow_k8 12168 0
speedstep_lib 4228 0
freq_table 4612 1 powernow_k8
slusb 16736 0
slamr 403016 2
snd_pcm_oss 59168 0
snd_mixer_oss 18944 1 snd_pcm_oss
snd_seq 51984 0
button 7056 0
battery 10244 0
ac 5252 0
edd 9824 0
af_packet 21384 2
joydev 9408 0
usb_storage 72512 0
scsi_mod 131304 1 usb_storage
usbhid 43616 0
ip6t_REJECT 5504 3
pcmcia 37176 0
firmware_class 9856 1 pcmcia
ipt_REJECT 5632 3
ipt_state 1920 12
iptable_mangle 2688 0
iptable_nat 22228 0
iptable_filter 2816 1
snd_via82xx 28096 1
ip6table_mangle 2304 0
gameport 14600 1 snd_via82xx
ip_conntrack 42168 2 ipt_state,iptable_nat
snd_ac97_codec 90876 1 snd_via82xx
ip_tables 19456 8 ipt_pkttype,ipt_LOG,ipt_limit,ipt_REJECT,ipt_state ,iptable_mangle,iptable_nat,iptable_filter
snd_ac97_bus 2432 1 snd_ac97_codec
snd_pcm 93064 3 snd_pcm_oss,snd_via82xx,snd_ac97_codec
ehci_hcd 32136 0
uhci_hcd 32016 0
via_rhine 22276 0
snd_timer 24452 2 snd_seq,snd_pcm
snd_page_alloc 10632 2 snd_via82xx,snd_pcm
snd_mpu401_uart 7296 1 snd_via82xx
mii 5504 1 via_rhine
i2c_viapro 8080 0
i2c_core 20368 1 i2c_viapro
snd_rawmidi 24864 1 snd_mpu401_uart
via_ircc 22164 0
irda 115000 1 via_ircc
crc_ccitt 2176 1 irda
snd_seq_device 8588 2 snd_seq,snd_rawmidi
ip6table_filter 2688 1
usbcore 112640 6 slusb,usb_storage,usbhid,ehci_hcd,uhci_hcd
ip6_tables 18176 3 ip6t_REJECT,ip6table_mangle,ip6table_filter
snd 60420 12 snd_pcm_oss,snd_mixer_oss,snd_seq,snd_via82xx,snd_ ac97_codec,snd_pcm,snd_timer,snd_mpu401_uart,snd_r awmidi,snd_seq_device
soundcore 9184 1 snd
generic 4484 0 [permanent]
yenta_socket 23820 2
rsrc_nonstatic 12800 1 yenta_socket
pcmcia_core 39952 3 pcmcia,yenta_socket,rsrc_nonstatic
ohci1394 32820 0
ieee1394 97208 1 ohci1394
amd64_agp 11976 1
agpgart 33096 1 amd64_agp
shpchp 88676 0
pci_hotplug 26164 1 shpchp
ipv6 242752 11 ip6t_REJECT
parport_pc 38980 1
lp 11460 0
parport 33864 2 parport_pc,lp
nls_iso8859_1 4096 1
nls_cp437 5760 1
vfat 12800 1
fat 49692 1 vfat
dm_mod 54972 0
reiserfs 250480 1
fan 4996 0
ide_cd 39684 0
cdrom 36896 1 ide_cd
thermal 14472 0
processor 24252 2 powernow_k8,thermal
via82cxxx 13212 0 [permanent]
ide_disk 17152 4
ide_core 122380 5 usb_storage,generic,ide_cd,via82cxxx,ide_disk
di seguito ho inserito il comando: fdisk -l
Disk /dev/hda: 40.0 GB, 40007761920 bytes
255 heads, 63 sectors/track, 4864 cylinders
Units = cilindri of 16065 * 512 = 8225280 bytes
Dispositivo Boot Start End Blocks Id System
/dev/hda1 * 1 3462 27808483+ c W95 FAT32 (LBA)
/dev/hda2 3463 4864 11261565 f W95 Ext'd (LBA)
/dev/hda5 3463 3528 530113+ 82 Linux swap / Solaris
/dev/hda6 3529 4864 10731388+ 83 Linux
a questo punto cosa devo fare, tenendo presente che la mia chiavetta è una VERBATIM da 1 GB e
che il sistema SUSE 10 mkdir si trovano su /media e non su /mnt
GRAZIEEEEEEEEEEEEEEEEE???????????????
controlla fdisk -l piu in basso per vedere se mette un altra sezione con sd
dai un dmesg | grep sd per vedere se riconosce la chiavetta
OT:è uscita la 10.2...leggete le migliorie
qui
"Disapprovo ciò che dici, ma difenderò alla morte il tuo diritto di dirlo." Voltaire
1100110011111000011
grazie dell'aiuto........
ho eseguito il comando dmesg ma credo che la chiavetta non la riconosce .............
Linux version 2.6.13-15.10-default (geeko@buildhost) (gcc version 4.0.2 20050901 (prerelease) (SUSE Linux)) #1 Fri May 12 16:27:12 UTC 2006
Kernel command line: root=/dev/hda6 vga=0x317 selinux=0 resume=/dev/hda5 splash=silent
bootsplash: silent mode.
Initializing CPU#0
PID hash table entries: 1024 (order: 10, 16384 bytes)
Detected 1601.211 MHz processor.
Using pmtmr for high-res timesource
Console: colour dummy device 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 253400k/261568k available (2029k kernel code, 7524k reserved, 695k data, 204k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 3205.57 BogoMIPS (lpj=6411143)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
PCI: PCI BIOS revision 2.10 entry at 0xfd557, last bus=1
PCI: Using configuration type 1
ACPI: Subsystem revision 20050408
Boot video device is 0000:01:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [ALKA] (IRQs 16 17 18 19 20 21 22 23) *10, disabled.
ACPI: PCI Interrupt Link [ALKB] (IRQs 16 17 18 19 20 21 22 23) *10, disabled.
ACPI: PCI Interrupt Link [ALKC] (IRQs 22) *11, disabled.
ACPI: PCI Interrupt Link [ALKD] (IRQs 21) *11, disabled.
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 9 12 14 15) *10
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 *10 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 9 10 *11 12 14 15)
ACPI: Embedded Controller [EC] (gpe 11)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 10 devices
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
TC classifier action (bugs to netdev@vger.kernel.org cc hadi@cyberus.ca)
pnp: 00:05: ioport range 0x600-0x60f has been reserved
pnp: 00:05: ioport range 0x1c0-0x1cf has been reserved
pnp: 00:05: ioport range 0x4d0-0x4d1 has been reserved
pnp: 00:05: ioport range 0xfe10-0xfe11 could not be reserved
PCI: Bridge: 0000:00:01.0
IO window: disabled.
MEM window: c1000000-c1ffffff
PREFETCH window: e0000000-efffffff
PCI: Bus 2, cardbus bridge: 0000:00:0b.0
IO window: 00002000-00002fff
IO window: 00003000-00003fff
PREFETCH window: 10000000-11ffffff
MEM window: 12000000-13ffffff
PCI: Bus 6, cardbus bridge: 0000:00:0b.1
IO window: 00005000-00005fff
IO window: 00006000-00006fff
PREFETCH window: 14000000-15ffffff
MEM window: 16000000-17ffffff
ACPI-0212: *** Warning: Device is not power manageable
PCI: Setting latency timer of device 0000:00:01.0 to 64
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:00:0b.0[A] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:0b.0 to 64
PCI: Enabling device 0000:00:0b.1 (0000 -> 0003)
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 9
PCI: setting IRQ 9 as level-triggered
Console: switching to colour frame buffer device 127x44
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing enabled
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
floppy0: no floppy controllers found
RAMDISK driver initialized: 16 RAM disks of 64000K size 1024 blocksize
loop: loaded (max 8 devices)
mice: PS/2 mouse device common for all mice
input: PC Speaker
md: md driver 0.90.2 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 3.38
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
NET: Registered protocol family 1
Using IPI Shortcut mode
ACPI wakeup devices:
PCI0 Z007 ILAN LID SLPB
ACPI: (supports S0 S3 S4 S5)
Freeing unused kernel memory: 204k freed
input: AT Translated Set 2 keyboard on isa0060/serio0
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:11.1
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:11.1[A] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11
PCI: Via IRQ fixup for 0000:00:11.1, from 0 to 11
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8235 (rev 00) IDE UDMA133 controller on pci0000:00:11.1
ide0: BM-DMA at 0x1c60-0x1c67, BIOS settings: hdaMA, hdb
io
ide1: BM-DMA at 0x1c68-0x1c6f, BIOS settings: hdc
Probing IDE interface ide0...
hda: HTS424040M9AT00, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: max request size: 1024KiB
hda: 78140160 sectors (40007 MB) w/1739KiB Cache, CHS=16383/255/63, UDMA(100)
hda: cache flushes supported
hda: hda1 hda2 < hda5 hda6 >
Probing IDE interface ide1...
Synaptics Touchpad, model: 1, fw: 5.8, id: 0x9248b1, caps: 0x904713/0x4000
input: SynPS/2 Synaptics TouchPad on isa0060/serio4
hdc: TSSTcorpCD/DVDW TS-L532A, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
ACPI: CPU0 (power states: C1[C1])
ACPI: Thermal Zone [THRS] (25 C)
ACPI: Thermal Zone [THRC] (42 C)
Attempting manual resume
hdc: ATAPI 24X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
swsusp: Suspend partition has wrong signature?
ReiserFS: hda6: found reiserfs format "3.6" with standard journal
ReiserFS: hda6: using ordered data mode
ReiserFS: hda6: journal params: device hda6, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hda6: checking transaction log (hda6)
ReiserFS: hda6: Using r5 hash to sort names
bootsplash: status on console 0 changed to on
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@redhat.com
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
lp0: using parport0 (interrupt-driven).
Adding 530104k swap on /dev/hda5. Priority:-1 extents:1
NET: Registered protocol family 10
Disabled Privacy Extensions on device c036b920(lo)
IPv6 over IPv4 tunneling driver
ip6_tables: (C) 2000-2002 Netfilter core team
ip_tables: (C) 2000-2002 Netfilter core team
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
ip_conntrack version 2.1 (2043 buckets, 16344 max) - 248 bytes per conntrack
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected AGP bridge 0
agpgart: AGP aperture is 256M @ 0xd0000000
ACPI: PCI Interrupt 0000:00:0b.0[A] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
Yenta: CardBus bridge found at 0000:00:0b.0 [1025:006e]
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v2.3
Yenta: ISA IRQ mask 0x0078, PCI irq 11
Socket status: 30000006
ACPI: PCI Interrupt 0000:00:0b.1[B] -> Link [LNKA] -> GSI 9 (level, low) -> IRQ 9
Yenta: CardBus bridge found at 0000:00:0b.1 [1025:006e]
ieee1394: Initialized config rom entry `ip1394'
Yenta: ISA IRQ mask 0x0078, PCI irq 9
Socket status: 30000006
ACPI-0212: *** Warning: Device is not power manageable
ACPI: PCI Interrupt 0000:00:10.0[A] -> Link [LNKA] -> GSI 9 (level, low) -> IRQ 9
PCI: Via IRQ fixup for 0000:00:10.0, from 0 to 9
uhci_hcd 0000:00:10.0: UHCI Host Controller
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:10.0: irq 9, io base 0x00001c00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ohci1394: $Rev: 1299 $ Ben Collins <bcollins@debian.org>
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:00:0b.2[C] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[10] MMIO=[c0005000-c00057ff] Max Packet=[2048]
ACPI-0212: *** Warning: Device is not power manageable
ACPI: PCI Interrupt 0000:00:10.1[B] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10
PCI: Via IRQ fixup for 0000:00:10.1, from 0 to 10
uhci_hcd 0000:00:10.1: UHCI Host Controller
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:10.1: irq 10, io base 0x00001c20
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI-0212: *** Warning: Device is not power manageable
ACPI: PCI Interrupt 0000:00:10.2[C] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11
PCI: Via IRQ fixup for 0000:00:10.2, from 0 to 11
uhci_hcd 0000:00:10.2: UHCI Host Controller
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:10.2: irq 11, io base 0x00001c40
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
usb 1-1: new low speed USB device using uhci_hcd and address 2
via-rhine.c:v1.10-LK1.2.0-2.6 June-10-2004 Written by Donald Becker
ACPI-0212: *** Warning: Device is not power manageable
ACPI-0402: *** Warning: Unable to derive IRQ for device 0000:00:12.0
ACPI: PCI Interrupt 0000:00:12.0[A]: no GSI - using IRQ 10
eth0: VIA Rhine II at 0x11800, 00:0a:e4:a3:71:e2, IRQ 10.
eth0: MII PHY found at address 1, status 0x7849 advertising 05e1 Link 0000.
irq 11: nobody cared (try booting with the "irqpoll" option)
[<d1259040>] (usb_hcd_irq+0x0/0x60 [usbcore])
Disabling IRQ #11
NET: Registered protocol family 23
via_ircc: module not supported by Novell, setting U taint flag.
ACPI-0212: *** Warning: Device is not power manageable
ACPI-0212: *** Warning: Device is not power manageable
ACPI: PCI Interrupt 0000:00:10.3[D] -> Link [LNKD] -> GSI 11 (lvel, low) -> IRQ 11
PCI: Via IRQ fixup for 0000:00:10.3, from 0 to 11
ehci_hcd 0000:00:10.3: EHCI Host Controller
ehci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4
ehci_hcd 0000:00:10.3: irq 11, io mem 0xc0005800
ehci_hcd 0000:00:10.3: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 6 ports detected
ACPI: PCI Interrupt 0000:00:11.5[C] -> Link [LNKA] -> GSI 9 (level, low) -> IRQ 9
PCI: Via IRQ fixup for 0000:00:11.5, from 11 to 9
PCI: Setting latency timer of device 0000:00:11.5 to 64
usb 1-1: USB disconnect, address 2
usb 1-1: new low speed USB device using uhci_hcd and address 3
usbcore: registered new driver hiddev
input: USB HID v1.10 Mouse [Acrox USB & PS/2 Mouse] on usb-0000:00:10.0-1
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.01:USB HID core driver
slamr: module not supported by Novell, setting U taint flag.
slamr: module license 'Smart Link Ltd.' taints kernel.
slamr: SmartLink AMRMO modem.
slamr: probe 1106:3068 VIA3058 card...
ACPI: PCI Interrupt 0000:00:11.6[C] -> Link [LNKA] -> GSI 9 (level, low) -> IRQ 9
PCI: Via IRQ fixup for 0000:00:11.6, from 11 to 9
PCI: Setting latency timer of device 0000:00:11.6 to 64
slamr: mc97 codec is SIL27
slamr: slamr0 is VIA3058 card.
usb 4-4: new high speed USB device using ehci_hcd and address 3
ehci_hcd 0000:00:10.3: Unlink after no-IRQ? Controller is probably using the wrong IRQ.
usb 4-4: device not accepting address 3, error -110
usb 4-4: new high speed USB device using ehci_hcd and address 4
usb 4-4: device not accepting address 4, error -110
usb 4-4: new high speed USB device using ehci_hcd and address 5
SFW2-OUT-ERROR IN= OUT=modem0 SRC=151.24.189.187 DST=66.249.91.104 LEN=40 TOS=0x00 PREC=0x00 TTL=64 ID=57690 DF PROTO=TCP SPT=6109 DPT=80 WINDOW=32767 RES=0x00 ACK FIN URGP=0
usb 4-4: device not accepting address 5, error -110
usb 4-4: new high speed USB device using ehci_hcd and address 6
grazie........
si è uscita x andarsi a fare una giratina , apri gli occhietti è il primo rilascio in alfatest
Permessi di invio
Rispondi quotando