Ciao sono nuovo del forum,ed ho un problema, io utilizzavo sul mio computer mandriva e windoz e mi connettevo normalmente con il mio modem (della wisecom esterno seriale 56K) su entrambi i sistemi. Ora però mi hanno consigliato di installare debian al posto di mandriva e li il modem non viene riconosciuto adesso non so come procedere
se gentilmente mi potete dare una mano ve ne sarei grato.
p.s. se vi dovesse essere d'aiuto la mia connessione e con telecom quella di 12 € al mese
se è un modem seriale viene riconosciuro sicuramente
le periferiche sull a porta com vengono usate tranquillamente
hai provato ad interrogare le varie porte avviando kppp ?
con debian semmai devi commentare la riga auth
#auth
nel file /etc/ppp/options
altrimenti si connette e si disconnette immediatamente
si ho provato ad interrogare il modem ma nn mi fa nulla
forse avrei dovuto anche dire che sono un po inesperto in materia......sono agli inizi......cmq di certo nn si connette e disconnette.con debian semmai devi commentare la riga auth
#auth
nel file /etc/ppp/options
altrimenti si connette e si disconnette immediatamente
mmmm mi spieghi sta cosa del commentare x favore??con debian semmai devi commentare la riga auth
#auth
nel file /etc/ppp/options
sembra strano a meno che tu non abbia problemi alle porte seriali
dai da terminale
dmesg | grep tty
e controlla che non esistano conflitti di irq
prova ad avviare gnome-ppp e controlla da li o scarica wvdial se non lo hai sui cd e prova con quello
fra poco povo poi posto i risultati
allora ho fatto dmesg ed mi e uscito questo
vedi che ci capisci che io francamentecodice:Linux version 2.4.27-2-386 (horms@tabatha.lab.ultramonkey.org) (gcc version 3.3.5 (Debian 1:3.3.5-12)) #1 Mon May 16 16:47:51 JST 2005 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000001ff40000 (usable) BIOS-e820: 000000001ff40000 - 000000001ff50000 (ACPI data) BIOS-e820: 000000001ff50000 - 0000000020000000 (ACPI NVS) 511MB LOWMEM available. On node 0 totalpages: 130880 zone(0): 4096 pages. zone(1): 126784 pages. zone(2): 0 pages. ACPI: RSDP (v000 ACPIAM ) @ 0x000f70c0 ACPI: RSDT (v001 INTEL D845PESV 0x20021020 MSFT 0x00000097) @ 0x1ff40000 ACPI: FADT (v002 INTEL D845PESV 0x20021020 MSFT 0x00000097) @ 0x1ff40200 ACPI: MADT (v001 INTEL D845PESV 0x20021020 MSFT 0x00000097) @ 0x1ff40300 ACPI: ASF! (v016 AMIASF I845GASF 0x00000001 MSFT 0x0100000d) @ 0x1ff44370 ACPI: DSDT (v001 INTEL D845PESV 0x0000010a MSFT 0x0100000d) @ 0x00000000 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) Processor #0 Pentium 4(tm) XEON(tm) APIC version 20 ACPI: LAPIC (acpi_id[0x02] lapic_id[0x81] disabled) Processor #129 invalid (max 16) ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x02] dfl dfl lint[0x1]) Kernel command line: root=/dev/hdb1 ro Found and enabled local APIC! Initializing CPU#0 Detected 2399.979 MHz processor. Console: colour VGA+ 80x25 Calibrating delay loop... 4784.12 BogoMIPS Memory: 511876k/523520k available (1069k kernel code, 11256k reserved, 459k data, 96k init, 0k highmem) Dentry cache hash table entries: 65536 (order: 7, 524288 bytes) Inode cache hash table entries: 32768 (order: 6, 262144 bytes) Mount cache hash table entries: 512 (order: 0, 4096 bytes) Buffer cache hash table entries: 32768 (order: 5, 131072 bytes) Page-cache hash table entries: 131072 (order: 7, 524288 bytes) CPU: Trace cache: 12K uops, L1 D cache: 8K CPU: L2 cache: 512K CPU: After generic, caps: bfebfbff 00000000 00000000 00000000 CPU: Common caps: bfebfbff 00000000 00000000 00000000 CPU: Intel(R) Pentium(R) 4 CPU 2.40GHz stepping 07 Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Checking 'hlt' instruction... OK. Checking for popad bug... OK. POSIX conformance testing by UNIFIX enabled ExtINT on CPU#0 ESR value before enabling vector: 00000000 ESR value after enabling vector: 00000000 Using local APIC timer interrupts. calibrating APIC timer ... ..... CPU clock speed is 2399.9956 MHz. ..... host bus clock speed is 133.3329 MHz. cpu: 0, clocks: 1333329, slice: 666664 CPU0<T0:1333328,T1:666656,D:8,S:666664,C:1333329> ACPI: Subsystem revision 20040326 ACPI: Interpreter disabled. PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=2 PCI: Using configuration type 1 PCI: Probing PCI hardware PCI: ACPI tables contain no PCI IRQ routing entries PCI: Probing PCI hardware (bus 00) PCI: Ignoring BAR0-3 of IDE controller 00:1f.1 Transparent bridge - Intel Corp. 82801BA/CA/DB/EB PCI Bridge PCI: Using IRQ router PIIX/ICH [8086/24c0] at 00:1f.0 PCI: Found IRQ 9 for device 00:1f.1 PCI: Sharing IRQ 9 with 00:1d.2 Linux NET4.0 for Linux 2.4 Based upon Swansea University Computer Society NET3.039 Initializing RT netlink socket Starting kswapd VFS: Disk quotas vdquot_6.5.1 devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au) devfs: boot_options: 0x0 pty: 256 Unix98 ptys configured Serial driver version 5.05c (2001-07-08) with HUB-6 MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI enabled ttyS00 at 0x03f8 (irq = 4) is a 16550A PCI: Found IRQ 5 for device 02:03.0 PCI: Sharing IRQ 5 with 00:1d.1 Redundant entry in serial pci_table. Please send the output of lspci -vv, this message (1057,3052,1057,3020) and the manufacturer and name of serial board or modem board to serial-pci-info@lists.sourceforge.net. register_serial(): autoconfig failed COMX: driver version 0.85 (C) 1995-1999 ITConsult-Pro Co. <info@itc.hu> RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize Initializing Cryptographic API NET4: Linux TCP/IP 1.0 for NET4.0 IP: routing cache hash table of 4096 buckets, 32Kbytes TCP: Hash tables configured (established 32768 bind 65536) Linux IP multicast router 0.06 plus PIM-SM RAMDISK: cramfs filesystem found at block 0 RAMDISK: Loading 3692 blocks [1 disk] into ram disk... done. Freeing initrd memory: 3692k freed VFS: Mounted root (cramfs filesystem). Freeing unused kernel memory: 96k freed NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx ide: late registration of driver. ICH4: IDE controller at PCI slot 00:1f.1 PCI: Enabling device 00:1f.1 (0005 -> 0007) PCI: Found IRQ 9 for device 00:1f.1 PCI: Sharing IRQ 9 with 00:1d.2 ICH4: chipset revision 2 ICH4: not 100% native mode: will probe irqs later ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:DMA ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:DMA, hdd:DMA hda: Maxtor 6Y080L0, ATA DISK drive hdb: ST315323A, ATA DISK drive blk: queue e0825b60, I/O limit 4095Mb (mask 0xffffffff) blk: queue e0825c9c, I/O limit 4095Mb (mask 0xffffffff) hdc: GENERIC DVD RW 8XMax, ATAPI CD/DVD-ROM drive hdd: HL-DT-ST RW/DVD GCC-4480B, ATAPI CD/DVD-ROM drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 ide1 at 0x170-0x177,0x376 on irq 15 hda: attached ide-disk driver. hda: 160086528 sectors (81964 MB) w/2048KiB Cache, CHS=158816/16/63, UDMA(100) hdb: attached ide-disk driver. hdb: 30008475 sectors (15364 MB) w/512KiB Cache, CHS=29770/16/63, UDMA(66) Partition check: /dev/ide/host0/bus0/target0/lun0: [PTBL] [9964/255/63] p1 /dev/ide/host0/bus0/target1/lun0: [PTBL] [1867/255/63] p1 Journalled Block Device driver loaded EXT3-fs: INFO: recovery required on readonly filesystem. EXT3-fs: write access will be enabled during recovery. kjournald starting. Commit interval 5 seconds EXT3-fs: recovery complete. EXT3-fs: mounted filesystem with ordered data mode. EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,65), internal journal Real Time Clock Driver v1.10f hdc: attached ide-cdrom driver. hdc: ATAPI 40X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33) Uniform CD-ROM driver Revision: 3.12 hdd: attached ide-cdrom driver. hdd: ATAPI 40X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33) 8139too Fast Ethernet driver 0.9.26 PCI: Found IRQ 11 for device 02:01.0 eth0: RealTek RTL8139 at 0xd800, 00:40:f4:d1:73:98, IRQ 11 eth0: Identified 8139 chip type 'RTL-8100B/8139D' SCSI subsystem driver Revision: 1.00 scsi0 : SCSI host adapter emulation for IDE ATAPI devices Intel 810 + AC97 Audio, version 1.01, 16:51:32 May 16 2005 PCI: Found IRQ 3 for device 00:1f.5 PCI: Sharing IRQ 3 with 00:1f.3 PCI: Setting latency timer of device 00:1f.5 to 64 i810: Intel ICH4 found at IO 0xe080 and 0xe400, MEM 0xfebff800 and 0xfebff400, IRQ 3 i810: Intel ICH4 mmio at 0xe089b800 and 0xe089d400 i810_audio: Primary codec has ID 2 i810_audio: Audio Controller supports 6 channels. i810_audio: Defaulting to base 2 channel mode. i810_audio: Resetting connection 0 i810_audio: Connection 0 with codec id 2 ac97_codec: AC97 Audio codec, id: ADS116 (Unknown) i810_audio: AC'97 codec 2 supports AMAP, total channels = 2 usb.c: registered new driver usbdevfs usb.c: registered new driver hub usb-uhci.c: $Revision: 1.275 $ time 16:52:03 May 16 2005 usb-uhci.c: High bandwidth mode enabled PCI: Found IRQ 11 for device 00:1d.0 PCI: Setting latency timer of device 00:1d.0 to 64 usb-uhci.c: USB UHCI at I/O 0xe800, IRQ 11 usb-uhci.c: Detected 2 ports usb.c: new USB bus registered, assigned bus number 1 hub.c: USB hub found hub.c: 2 ports detected PCI: Found IRQ 5 for device 00:1d.1 PCI: Sharing IRQ 5 with 02:03.0 PCI: Setting latency timer of device 00:1d.1 to 64 usb-uhci.c: USB UHCI at I/O 0xe880, IRQ 5 usb-uhci.c: Detected 2 ports usb.c: new USB bus registered, assigned bus number 2 hub.c: USB hub found hub.c: 2 ports detected PCI: Found IRQ 9 for device 00:1d.2 PCI: Sharing IRQ 9 with 00:1f.1 PCI: Setting latency timer of device 00:1d.2 to 64 usb-uhci.c: USB UHCI at I/O 0xec00, IRQ 9 usb-uhci.c: Detected 2 ports usb.c: new USB bus registered, assigned bus number 3 hub.c: USB hub found hub.c: 2 ports detected usb-uhci.c: v1.275:USB Universal Host Controller Interface driver hub.c: new USB device 00:1d.0-1, assigned address 2 usb.c: USB device 2 (vend/prod 0x3f0/0x405) is not claimed by any active driver.PCI: Found IRQ 10 for device 00:1d.7 PCI: Setting latency timer of device 00:1d.7 to 64 ehci_hcd 00:1d.7: Intel Corp. 82801DB USB2 ehci_hcd 00:1d.7: irq 10, pci mem e08b8c00 usb.c: new USB bus registered, assigned bus number 4 ehci_hcd 00:1d.7: enabled 64bit PCI DMA PCI: cache line size of 128 is not supported by device 00:1d.7 ehci_hcd 00:1d.7: USB 2.0 enabled, EHCI 1.00, driver 2003-Dec-29/2.4 usb.c: USB disconnect on device 00:1d.0-1 address 2 hub.c: USB hub found hub.c: 6 ports detected hub.c: new USB device 00:1d.0-1, assigned address 3 usb.c: USB device 3 (vend/prod 0x3f0/0x405) is not claimed by any active driver.8139cp: 10/100 PCI Ethernet driver v1.2 (Mar 22, 2004) pci_hotplug: PCI Hot Plug PCI Core version: 0.5 shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x1001 pci_hotplug: PCI Hot Plug PCI Core version: 0.5 pciehp: acpi_pciehprm:get_device PCI ROOT HID fail=0x1001 i810_rng hardware driver 0.9.8 loaded hw_random: misc device register failed uhci.c: USB Universal Host Controller Interface driver v1.1 NET4: AppleTalk 0.18a for Linux NET4.0 apm: BIOS not found.
poi ho fatto grep tty nn andava cosi ho provato a vedere come funzionava il comando grep ma ......
gnome-ppp nn va
poi facendo kppp all'avvio dice che nn trova un file e che lo debbo creare anche vuoto, come si fa?
e ancora qual'e la porta seriale del modem cioe qual'e è tra le varie tty1 ,tty2 e compagnia bella???
scusa se ti ho assaltato dalle domande ma è che nn sono ancora capace.
in effetti il computer sembra avere problemi con le seriali
register_serial(): autoconfig failed
e per quello non si connette
hai installato debian con il kernel 2.4
puoi provare ad installare il kernel 2.6
(lo hai sui cd )
dai un apt-cache search kernel-image
e installa il pacchetto del kernel 2.6 disponibile
apt-get install kernel-image-2.6.8-2-386 (probabilmente )
il kernel fa tutto da se molto probabilmente al riavvio risolve anche il problema delle seriali
all'inizio dell' installazione invece di dare invio se vuoi installare direttamente con il kernel 2.6 devi scrivere linux26 poi dare invio
per la loca me l'avevano detto!!all'inizio dell' installazione invece di dare invio se vuoi installare direttamente con il kernel 2.6 devi scrivere linux26 poi dare invio
o reinstallato tutto....adesso quando do dmesg esce questo
continuacodice:Linux version 2.6.8-2-386 (horms@tabatha.lab.ultramonkey.org) (gcc version 3.3.5 (Debian 1:3.3.5-12)) #1 Thu May 19 17:40:50 JST 2005 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000001ff40000 (usable) BIOS-e820: 000000001ff40000 - 000000001ff50000 (ACPI data) BIOS-e820: 000000001ff50000 - 0000000020000000 (ACPI NVS) 511MB LOWMEM available. On node 0 totalpages: 130880 DMA zone: 4096 pages, LIFO batch:1 Normal zone: 126784 pages, LIFO batch:16 HighMem zone: 0 pages, LIFO batch:1 DMI 2.3 present. ACPI: RSDP (v000 ACPIAM ) @ 0x000f70c0 ACPI: RSDT (v001 INTEL D845PESV 0x20021020 MSFT 0x00000097) @ 0x1ff40000 ACPI: FADT (v002 INTEL D845PESV 0x20021020 MSFT 0x00000097) @ 0x1ff40200 ACPI: MADT (v001 INTEL D845PESV 0x20021020 MSFT 0x00000097) @ 0x1ff40300 ACPI: ASF! (v016 AMIASF I845GASF 0x00000001 MSFT 0x0100000d) @ 0x1ff44370 ACPI: DSDT (v001 INTEL D845PESV 0x0000010a MSFT 0x0100000d) @ 0x00000000 ACPI: PM-Timer IO Port: 0x408 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) Processor #0 15:2 APIC version 20 ACPI: LAPIC (acpi_id[0x02] lapic_id[0x81] disabled) ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x02] dfl dfl lint[0x1]) ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0]) IOAPIC[0]: Assigned apic_id 1 IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) ACPI: IRQ0 used by override. ACPI: IRQ2 used by override. ACPI: IRQ9 used by override. Enabling APIC mode: Flat. Using 1 I/O APICs Using ACPI (MADT) for SMP configuration information Built 1 zonelists Kernel command line: root=/dev/hdb1 ro Initializing CPU#0 PID hash table entries: 2048 (order 11: 16384 bytes) Detected 2401.016 MHz processor. Using pmtmr for high-res timesource Console: colour VGA+ 80x25 Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Memory: 511100k/523520k available (1336k kernel code, 11644k reserved, 732k data, 204k init, 0k highmem) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay loop... 4751.36 BogoMIPS Security Scaffold v1.0.0 initialized Mount-cache hash table entries: 512 (order: 0, 4096 bytes) CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000 CPU: Trace cache: 12K uops, L1 D cache: 8K CPU: L2 cache: 512K CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080 CPU: Intel(R) Pentium(R) 4 CPU 2.40GHz stepping 07 Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Checking 'hlt' instruction... OK. Checking for popad bug... OK. enabled ExtINT on CPU#0 ESR value before enabling vector: 00000000 ESR value after enabling vector: 00000000 ENABLING IO-APIC IRQs init IO_APIC IRQs IO-APIC (apicid-pin) 1-0, 1-16, 1-17, 1-18, 1-19, 1-20, 1-21, 1-22, 1-23 not connected. ..TIMER: vector=0x31 pin1=2 pin2=-1 Using local APIC timer interrupts. calibrating APIC timer ... ..... CPU clock speed is 2399.0526 MHz. ..... host bus clock speed is 133.0306 MHz. checking if image is initramfs...it isn't (ungzip failed); looks like an initrd Freeing initrd memory: 4216k freed NET: Registered protocol family 16 EISA bus registered PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=2 PCI: Using configuration type 1 mtrr: v2.0 (20020519) ACPI: Subsystem revision 20040326 ACPI: Interpreter enabled ACPI: Using IOAPIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (00:00) PCI: Probing PCI hardware (bus 00) PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1 PCI: Transparent bridge - 0000:00:1e.0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT] ACPI: Power Resource [URP1] (off) ACPI: Power Resource [FDDP] (off) ACPI: Power Resource [LPTP] (off) ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 9 10 *11 12 14 15) ACPI: PCI Interrupt Link [LNKB] (IRQs *3 4 5 7 9 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 *9 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 7 9 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 *11 12 14 15) ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 *10 11 12 14 15) Linux Plug and Play Support v0.97 (c) Adam Belay PnPBIOS: Scanning system for PnP BIOS support... PnPBIOS: Found PnP BIOS installation structure at 0xc00f4850 PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0x4e8a, dseg 0xf0000 pnp: 00:0b: ioport range 0x4d0-0x4d1 has been reserved pnp: 00:0b: ioport range 0xcf8-0xcff could not be reserved PnPBIOS: 16 nodes reported by PnP BIOS; 16 recorded by driver PCI: Using ACPI for IRQ routing ACPI: PCI interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 169 ACPI: PCI interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 177 ACPI: PCI interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 185 ACPI: PCI interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 193 ACPI: PCI interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 185 ACPI: PCI interrupt 0000:00:1f.3[B] -> GSI 17 (level, low) -> IRQ 201 ACPI: PCI interrupt 0000:00:1f.5[B] -> GSI 17 (level, low) -> IRQ 201 ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 169 ACPI: PCI interrupt 0000:02:01.0[A] -> GSI 22 (level, low) -> IRQ 209 ACPI: PCI interrupt 0000:02:03.0[A] -> GSI 19 (level, low) -> IRQ 177 number of MP IRQ sources: 15. number of IO-APIC #1 registers: 24. testing the IO APIC....................... IO APIC #1...... .... register #00: 01000000 ....... : physical APIC id: 01 ....... : Delivery Type: 0 ....... : LTS : 0 .... register #01: 00178020 ....... : max redirection entries: 0017 ....... : PRQ implemented: 1 ....... : IO APIC version: 0020 .... register #02: 00000000 ....... : arbitration: 00 .... register #03: 00000001 ....... : Boot DT : 1 .... IRQ redirection table: NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect: 00 000 00 1 0 0 0 0 0 0 00 01 001 01 0 0 0 0 0 1 1 39 02 001 01 0 0 0 0 0 1 1 31 03 001 01 0 0 0 0 0 1 1 41 04 001 01 0 0 0 0 0 1 1 49 05 001 01 0 0 0 0 0 1 1 51 06 001 01 0 0 0 0 0 1 1 59 07 001 01 0 0 0 0 0 1 1 61 08 001 01 0 0 0 0 0 1 1 69 09 001 01 0 1 0 0 0 1 1 71 0a 001 01 0 0 0 0 0 1 1 79 0b 001 01 0 0 0 0 0 1 1 81 0c 001 01 0 0 0 0 0 1 1 89 0d 001 01 0 0 0 0 0 1 1 91 0e 001 01 0 0 0 0 0 1 1 99 0f 001 01 0 0 0 0 0 1 1 A1 10 001 01 1 1 0 1 0 1 1 A9 11 001 01 1 1 0 1 0 1 1 C9 12 001 01 1 1 0 1 0 1 1 B9 13 001 01 1 1 0 1 0 1 1 B1 14 000 00 1 0 0 0 0 0 0 00 15 000 00 1 0 0 0 0 0 0 00 16 001 01 1 1 0 1 0 1 1 D1 17 001 01 1 1 0 1 0 1 1 C1 Using vector-based indexing IRQ to pin mappings: IRQ0 -> 0:2 IRQ1 -> 0:1 IRQ3 -> 0:3 IRQ4 -> 0:4 IRQ5 -> 0:5 IRQ6 -> 0:6 IRQ7 -> 0:7 IRQ8 -> 0:8 IRQ9 -> 0:9 IRQ10 -> 0:10 IRQ11 -> 0:11 IRQ12 -> 0:12 IRQ13 -> 0:13 IRQ14 -> 0:14 IRQ15 -> 0:15 IRQ169 -> 0:16 IRQ201 -> 0:17 IRQ185 -> 0:18 IRQ177 -> 0:19 IRQ209 -> 0:22 IRQ193 -> 0:23 .................................... done.
Permessi di invio
Rispondi quotando