PDA

Visualizza la versione completa : [debian]connessione 56k


smoke
18-06-2006, 23:18
Ciao sono nuovo del forum, :) ed ho un problema, io utilizzavo sul mio computer mandriva e windoz e mi connettevo normalmente con il mio modem (della wisecom esterno seriale 56K) su entrambi i sistemi. Ora per mi hanno consigliato di installare debian al posto di mandriva e li il modem non viene riconosciuto adesso non so come procedere :confused: se gentilmente mi potete dare una mano ve ne sarei grato.


p.s. se vi dovesse essere d'aiuto la mia connessione e con telecom quella di 12 al mese

andy caps
18-06-2006, 23:24
se un modem seriale viene riconosciuro sicuramente

le periferiche sull a porta com vengono usate tranquillamente

hai provato ad interrogare le varie porte avviando kppp ?

con debian semmai devi commentare la riga auth
#auth

nel file /etc/ppp/options
altrimenti si connette e si disconnette immediatamente

smoke
18-06-2006, 23:28
si ho provato ad interrogare il modem ma nn mi fa nulla


con debian semmai devi commentare la riga auth
#auth

nel file /etc/ppp/options
altrimenti si connette e si disconnette immediatamente

forse avrei dovuto anche dire che sono un po inesperto in materia......sono agli inizi......cmq di certo nn si connette e disconnette.

smoke
18-06-2006, 23:57
con debian semmai devi commentare la riga auth
#auth

nel file /etc/ppp/options

mmmm mi spieghi sta cosa del commentare x favore??

andy caps
19-06-2006, 00:01
sembra strano a meno che tu non abbia problemi alle porte seriali

dai da terminale
dmesg | grep tty
e controlla che non esistano conflitti di irq


prova ad avviare gnome-ppp e controlla da li o scarica wvdial se non lo hai sui cd e prova con quello

smoke
19-06-2006, 00:04
fra poco povo poi posto i risultati

smoke
19-06-2006, 00:46
allora ho fatto dmesg ed mi e uscito questo


Linux version 2.4.27-2-386 (horms@tabatha.lab.ultramonkey.org) (gcc version 3.3.5 (Debian 1:3.3.5-12)) #1 Mon May 16 16:47:51 JST 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001ff40000 (usable)
BIOS-e820: 000000001ff40000 - 000000001ff50000 (ACPI data)
BIOS-e820: 000000001ff50000 - 0000000020000000 (ACPI NVS)
511MB LOWMEM available.
On node 0 totalpages: 130880
zone(0): 4096 pages.
zone(1): 126784 pages.
zone(2): 0 pages.
ACPI: RSDP (v000 ACPIAM ) @ 0x000f70c0
ACPI: RSDT (v001 INTEL D845PESV 0x20021020 MSFT 0x00000097) @ 0x1ff40000
ACPI: FADT (v002 INTEL D845PESV 0x20021020 MSFT 0x00000097) @ 0x1ff40200
ACPI: MADT (v001 INTEL D845PESV 0x20021020 MSFT 0x00000097) @ 0x1ff40300
ACPI: ASF! (v016 AMIASF I845GASF 0x00000001 MSFT 0x0100000d) @ 0x1ff44370
ACPI: DSDT (v001 INTEL D845PESV 0x0000010a MSFT 0x0100000d) @ 0x00000000
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 Pentium 4(tm) XEON(tm) APIC version 20
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x81] disabled)
Processor #129 invalid (max 16)
ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x02] dfl dfl lint[0x1])
Kernel command line: root=/dev/hdb1 ro
Found and enabled local APIC!
Initializing CPU#0
Detected 2399.979 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 4784.12 BogoMIPS
Memory: 511876k/523520k available (1069k kernel code, 11256k reserved, 459k data, 96k init, 0k highmem)
Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
Inode cache hash table entries: 32768 (order: 6, 262144 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 32768 (order: 5, 131072 bytes)
Page-cache hash table entries: 131072 (order: 7, 524288 bytes)
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: After generic, caps: bfebfbff 00000000 00000000 00000000
CPU: Common caps: bfebfbff 00000000 00000000 00000000
CPU: Intel(R) Pentium(R) 4 CPU 2.40GHz stepping 07
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
Checking for popad bug... OK.
POSIX conformance testing by UNIFIX
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 2399.9956 MHz.
..... host bus clock speed is 133.3329 MHz.
cpu: 0, clocks: 1333329, slice: 666664
CPU0<T0:1333328,T1:666656,D:8,S:666664,C:1333329>
ACPI: Subsystem revision 20040326
ACPI: Interpreter disabled.
PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=2
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: ACPI tables contain no PCI IRQ routing entries
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller 00:1f.1
Transparent bridge - Intel Corp. 82801BA/CA/DB/EB PCI Bridge
PCI: Using IRQ router PIIX/ICH [8086/24c0] at 00:1f.0
PCI: Found IRQ 9 for device 00:1f.1
PCI: Sharing IRQ 9 with 00:1d.2
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
VFS: Disk quotas vdquot_6.5.1
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with HUB-6 MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
PCI: Found IRQ 5 for device 02:03.0
PCI: Sharing IRQ 5 with 00:1d.1
Redundant entry in serial pci_table. Please send the output of
lspci -vv, this message (1057,3052,1057,3020)
and the manufacturer and name of serial board or modem board
to serial-pci-info@lists.sourceforge.net.
register_serial(): autoconfig failed
COMX: driver version 0.85 (C) 1995-1999 ITConsult-Pro Co. <info@itc.hu>
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
Initializing Cryptographic API
NET4: Linux TCP/IP 1.0 for NET4.0
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 65536)
Linux IP multicast router 0.06 plus PIM-SM
RAMDISK: cramfs filesystem found at block 0
RAMDISK: Loading 3692 blocks [1 disk] into ram disk... done.
Freeing initrd memory: 3692k freed
VFS: Mounted root (cramfs filesystem).
Freeing unused kernel memory: 96k freed
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ide: late registration of driver.
ICH4: IDE controller at PCI slot 00:1f.1
PCI: Enabling device 00:1f.1 (0005 -> 0007)
PCI: Found IRQ 9 for device 00:1f.1
PCI: Sharing IRQ 9 with 00:1d.2
ICH4: chipset revision 2
ICH4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:DMA, hdd:DMA
hda: Maxtor 6Y080L0, ATA DISK drive
hdb: ST315323A, ATA DISK drive
blk: queue e0825b60, I/O limit 4095Mb (mask 0xffffffff)
blk: queue e0825c9c, I/O limit 4095Mb (mask 0xffffffff)
hdc: GENERIC DVD RW 8XMax, ATAPI CD/DVD-ROM drive
hdd: HL-DT-ST RW/DVD GCC-4480B, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: attached ide-disk driver.
hda: 160086528 sectors (81964 MB) w/2048KiB Cache, CHS=158816/16/63, UDMA(100)
hdb: attached ide-disk driver.
hdb: 30008475 sectors (15364 MB) w/512KiB Cache, CHS=29770/16/63, UDMA(66)
Partition check:
/dev/ide/host0/bus0/target0/lun0: [PTBL] [9964/255/63] p1
/dev/ide/host0/bus0/target1/lun0: [PTBL] [1867/255/63] p1
Journalled Block Device driver loaded
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
kjournald starting. Commit interval 5 seconds
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,65), internal journal
Real Time Clock Driver v1.10f
hdc: attached ide-cdrom driver.
hdc: ATAPI 40X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.12
hdd: attached ide-cdrom driver.
hdd: ATAPI 40X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
8139too Fast Ethernet driver 0.9.26
PCI: Found IRQ 11 for device 02:01.0
eth0: RealTek RTL8139 at 0xd800, 00:40:f4:d1:73:98, IRQ 11
eth0: Identified 8139 chip type 'RTL-8100B/8139D'
SCSI subsystem driver Revision: 1.00
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
Intel 810 + AC97 Audio, version 1.01, 16:51:32 May 16 2005
PCI: Found IRQ 3 for device 00:1f.5
PCI: Sharing IRQ 3 with 00:1f.3
PCI: Setting latency timer of device 00:1f.5 to 64
i810: Intel ICH4 found at IO 0xe080 and 0xe400, MEM 0xfebff800 and 0xfebff400, IRQ 3
i810: Intel ICH4 mmio at 0xe089b800 and 0xe089d400
i810_audio: Primary codec has ID 2
i810_audio: Audio Controller supports 6 channels.
i810_audio: Defaulting to base 2 channel mode.
i810_audio: Resetting connection 0
i810_audio: Connection 0 with codec id 2
ac97_codec: AC97 Audio codec, id: ADS116 (Unknown)
i810_audio: AC'97 codec 2 supports AMAP, total channels = 2
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.275 $ time 16:52:03 May 16 2005
usb-uhci.c: High bandwidth mode enabled
PCI: Found IRQ 11 for device 00:1d.0
PCI: Setting latency timer of device 00:1d.0 to 64
usb-uhci.c: USB UHCI at I/O 0xe800, IRQ 11
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Found IRQ 5 for device 00:1d.1
PCI: Sharing IRQ 5 with 02:03.0
PCI: Setting latency timer of device 00:1d.1 to 64
usb-uhci.c: USB UHCI at I/O 0xe880, IRQ 5
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Found IRQ 9 for device 00:1d.2
PCI: Sharing IRQ 9 with 00:1f.1
PCI: Setting latency timer of device 00:1d.2 to 64
usb-uhci.c: USB UHCI at I/O 0xec00, IRQ 9
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 3
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
hub.c: new USB device 00:1d.0-1, assigned address 2
usb.c: USB device 2 (vend/prod 0x3f0/0x405) is not claimed by any active driver.PCI: Found IRQ 10 for device 00:1d.7
PCI: Setting latency timer of device 00:1d.7 to 64
ehci_hcd 00:1d.7: Intel Corp. 82801DB USB2
ehci_hcd 00:1d.7: irq 10, pci mem e08b8c00
usb.c: new USB bus registered, assigned bus number 4
ehci_hcd 00:1d.7: enabled 64bit PCI DMA
PCI: cache line size of 128 is not supported by device 00:1d.7
ehci_hcd 00:1d.7: USB 2.0 enabled, EHCI 1.00, driver 2003-Dec-29/2.4
usb.c: USB disconnect on device 00:1d.0-1 address 2
hub.c: USB hub found
hub.c: 6 ports detected
hub.c: new USB device 00:1d.0-1, assigned address 3
usb.c: USB device 3 (vend/prod 0x3f0/0x405) is not claimed by any active driver.8139cp: 10/100 PCI Ethernet driver v1.2 (Mar 22, 2004)
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x1001
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
pciehp: acpi_pciehprm:get_device PCI ROOT HID fail=0x1001
i810_rng hardware driver 0.9.8 loaded
hw_random: misc device register failed
uhci.c: USB Universal Host Controller Interface driver v1.1
NET4: AppleTalk 0.18a for Linux NET4.0
apm: BIOS not found.

vedi che ci capisci che io francamente :confused:

poi ho fatto grep tty nn andava cosi ho provato a vedere come funzionava il comando grep ma ...... :confused:

gnome-ppp nn va

poi facendo kppp all'avvio dice che nn trova un file e che lo debbo creare anche vuoto, come si fa?

e ancora qual'e la porta seriale del modem cioe qual'e tra le varie tty1 ,tty2 e compagnia bella???

scusa se ti ho assaltato dalle domande ma che nn sono ancora capace. :(

andy caps
19-06-2006, 01:00
in effetti il computer sembra avere problemi con le seriali

register_serial(): autoconfig failed
e per quello non si connette

hai installato debian con il kernel 2.4

puoi provare ad installare il kernel 2.6
(lo hai sui cd )

dai un apt-cache search kernel-image
e installa il pacchetto del kernel 2.6 disponibile
apt-get install kernel-image-2.6.8-2-386 (probabilmente )

il kernel fa tutto da se molto probabilmente al riavvio risolve anche il problema delle seriali


all'inizio dell' installazione invece di dare invio se vuoi installare direttamente con il kernel 2.6 devi scrivere linux26 poi dare invio

smoke
19-06-2006, 01:06
all'inizio dell' installazione invece di dare invio se vuoi installare direttamente con il kernel 2.6 devi scrivere linux26 poi dare invio

per la loca me l'avevano detto!! :( vabe ora vado e ti dico come e andata

smoke
19-06-2006, 02:03
o reinstallato tutto....adesso quando do dmesg esce questo


Linux version 2.6.8-2-386 (horms@tabatha.lab.ultramonkey.org) (gcc version 3.3.5 (Debian 1:3.3.5-12)) #1 Thu May 19 17:40:50 JST 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001ff40000 (usable)
BIOS-e820: 000000001ff40000 - 000000001ff50000 (ACPI data)
BIOS-e820: 000000001ff50000 - 0000000020000000 (ACPI NVS)
511MB LOWMEM available.
On node 0 totalpages: 130880
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 126784 pages, LIFO batch:16
HighMem zone: 0 pages, LIFO batch:1
DMI 2.3 present.
ACPI: RSDP (v000 ACPIAM ) @ 0x000f70c0
ACPI: RSDT (v001 INTEL D845PESV 0x20021020 MSFT 0x00000097) @ 0x1ff40000
ACPI: FADT (v002 INTEL D845PESV 0x20021020 MSFT 0x00000097) @ 0x1ff40200
ACPI: MADT (v001 INTEL D845PESV 0x20021020 MSFT 0x00000097) @ 0x1ff40300
ACPI: ASF! (v016 AMIASF I845GASF 0x00000001 MSFT 0x0100000d) @ 0x1ff44370
ACPI: DSDT (v001 INTEL D845PESV 0x0000010a MSFT 0x0100000d) @ 0x00000000
ACPI: PM-Timer IO Port: 0x408
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 15:2 APIC version 20
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x81] disabled)
ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x02] dfl dfl lint[0x1])
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: Assigned apic_id 1
IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Built 1 zonelists
Kernel command line: root=/dev/hdb1 ro
Initializing CPU#0
PID hash table entries: 2048 (order 11: 16384 bytes)
Detected 2401.016 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 511100k/523520k available (1336k kernel code, 11644k reserved, 732k data, 204k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 4751.36 BogoMIPS
Security Scaffold v1.0.0 initialized
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000
CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080
CPU: Intel(R) Pentium(R) 4 CPU 2.40GHz stepping 07
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
Checking for popad bug... OK.
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
ENABLING IO-APIC IRQs
init IO_APIC IRQs
IO-APIC (apicid-pin) 1-0, 1-16, 1-17, 1-18, 1-19, 1-20, 1-21, 1-22, 1-23 not connected.
..TIMER: vector=0x31 pin1=2 pin2=-1
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 2399.0526 MHz.
..... host bus clock speed is 133.0306 MHz.
checking if image is initramfs...it isn't (ungzip failed); looks like an initrd
Freeing initrd memory: 4216k freed
NET: Registered protocol family 16
EISA bus registered
PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=2
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20040326
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
ACPI: Power Resource [URP1] (off)
ACPI: Power Resource [FDDP] (off)
ACPI: Power Resource [LPTP] (off)
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs *3 4 5 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
PnPBIOS: Scanning system for PnP BIOS support...
PnPBIOS: Found PnP BIOS installation structure at 0xc00f4850
PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0x4e8a, dseg 0xf0000
pnp: 00:0b: ioport range 0x4d0-0x4d1 has been reserved
pnp: 00:0b: ioport range 0xcf8-0xcff could not be reserved
PnPBIOS: 16 nodes reported by PnP BIOS; 16 recorded by driver
PCI: Using ACPI for IRQ routing
ACPI: PCI interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 169
ACPI: PCI interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 177
ACPI: PCI interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 185
ACPI: PCI interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 193
ACPI: PCI interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 185
ACPI: PCI interrupt 0000:00:1f.3[B] -> GSI 17 (level, low) -> IRQ 201
ACPI: PCI interrupt 0000:00:1f.5[B] -> GSI 17 (level, low) -> IRQ 201
ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 169
ACPI: PCI interrupt 0000:02:01.0[A] -> GSI 22 (level, low) -> IRQ 209
ACPI: PCI interrupt 0000:02:03.0[A] -> GSI 19 (level, low) -> IRQ 177
number of MP IRQ sources: 15.
number of IO-APIC #1 registers: 24.
testing the IO APIC.......................
IO APIC #1......
.... register #00: 01000000
....... : physical APIC id: 01
....... : Delivery Type: 0
....... : LTS : 0
.... register #01: 00178020
....... : max redirection entries: 0017
....... : PRQ implemented: 1
....... : IO APIC version: 0020
.... register #02: 00000000
....... : arbitration: 00
.... register #03: 00000001
....... : Boot DT : 1
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 000 00 1 0 0 0 0 0 0 00
01 001 01 0 0 0 0 0 1 1 39
02 001 01 0 0 0 0 0 1 1 31
03 001 01 0 0 0 0 0 1 1 41
04 001 01 0 0 0 0 0 1 1 49
05 001 01 0 0 0 0 0 1 1 51
06 001 01 0 0 0 0 0 1 1 59
07 001 01 0 0 0 0 0 1 1 61
08 001 01 0 0 0 0 0 1 1 69
09 001 01 0 1 0 0 0 1 1 71
0a 001 01 0 0 0 0 0 1 1 79
0b 001 01 0 0 0 0 0 1 1 81
0c 001 01 0 0 0 0 0 1 1 89
0d 001 01 0 0 0 0 0 1 1 91
0e 001 01 0 0 0 0 0 1 1 99
0f 001 01 0 0 0 0 0 1 1 A1
10 001 01 1 1 0 1 0 1 1 A9
11 001 01 1 1 0 1 0 1 1 C9
12 001 01 1 1 0 1 0 1 1 B9
13 001 01 1 1 0 1 0 1 1 B1
14 000 00 1 0 0 0 0 0 0 00
15 000 00 1 0 0 0 0 0 0 00
16 001 01 1 1 0 1 0 1 1 D1
17 001 01 1 1 0 1 0 1 1 C1
Using vector-based indexing
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ5 -> 0:5
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ9 -> 0:9
IRQ10 -> 0:10
IRQ11 -> 0:11
IRQ12 -> 0:12
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
IRQ169 -> 0:16
IRQ201 -> 0:17
IRQ185 -> 0:18
IRQ177 -> 0:19
IRQ209 -> 0:22
IRQ193 -> 0:23
.................................... done.


continua

Loading